- 您现在的位置：买卖IC网 > PDF目录19751 > MAX5965AUAX+T (Maxim Integrated)IC PSE CTRLR FOR POE 36SSOP PDF资料下载
参数资料
| 型号： | MAX5965AUAX+T |
| 厂商： | Maxim Integrated |
| 文件页数： | 21/54页 |
| 文件大小： | 1334K |
| 描述： | IC PSE CTRLR FOR POE 36SSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 1,000 |
| 类型： | 以太网供电控制器（PoE） |
| 应用： | IP 电话，LAN 网络供电，网络路由器和交换机 |
| 内部开关： | 无 |
| 电源电压： | 2.4 V ~ 3.6 V |
| 工作温度： | 0°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 36-BSOP（0.295"，7.50mm 宽） |
| 供应商设备封装： | 36-SSOP |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页当前第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页
High-Power, Quad, Monolithic, PSE Controllers
for Power over Ethernet
______________________________________________________________________________________ 21
Overcurrent Protection
A sense resistor R
S
connected between SENSE_ and
V
EE
monitors the load current. Under normal operating
conditions, the voltage across R
S
(V
RS
) never exceeds
the threshold V
SU_LIM
. If V
RS
exceeds V
SU_LIM
, an
internal current-limiting circuit regulates the GATE_ volt-
age, limiting the current to I
LIM
= V
SU_LIM
/R
S
. During
transient conditions, if V
RS
exceeds V
SU_LIM
by more
than 1V, a fast pulldown circuit activates to quickly
recover from the current overshoot. During startup, if
the current-limit condition persists, when the startup
timer, t
START
, times out, the port shuts off, and the
STRT_FLT_ bit is set. In the normal powered state, the
MAX5965A/MAX5965B check for overcurrent condi-
tions as determined by V
FLT_LIM
= ~88% of V
SU_LIM
.
The t
FAULT
counter sets the maximum allowed continu-
ous overcurrent period. The t
FAULT
counter increases
when V
RS
exceeds V
FLT_LIM
and decreases at a slower
pace when V
RS
drops below V
FLT_LIM
. A slower decre-
ment for the t
FAULT
counter allows for detecting repeat-
ed short-duration overcurrents. When the counter
reaches the t
FAULT
limit, the MAX5965A/MAX5965B
power off the port and assert the IMAX_FLT_ bit. For a
continuous overstress, a fault latches exactly after a
period of t
FAULT
. V
SU_LIM
is programmable through the
ICUT registers R2Ah[6:4], R2Ah[2:0], R2Bh[6:4],
R2Bh[2:0], and the IVEE bits in register R29h[1:0]. See
the High-Power Mode section for more information on
the ICUT register.
After power-off due to an overcurrent fault, and if the
RSTR_EN bit is set, the t
FAULT
timer is not immediately
reset but starts decrementing at the same slower pace.
The MAX5965A/MAX5965B allow the port to be pow-
ered on only when the t
FAULT
counter is at zero. This
feature sets an automatic duty-cycle protection to the
external MOSFET avoiding overheating.
The MAX5965A/MAX5965B continuously flag when the
current exceeds the maximum current allowed for the
class as indicated in the CLASS status register. When
class overcurrent occurs, the MAX5965A/MAX5965B
set the IVC_ bit in register R09h.
ICUT Register and High-Power Mode
ICUT Register
The ICUT register determines the maximum current lim-
its allowed for each port of the MAX5965A/MAX5965B.
The 3 ICUT bits (R2Ah[6:4], R2Ah[2:0], R2Bh[6:4], and
R2Bh[2:0]) allow programming of the current-limit and
overcurrent thresholds in excess of the IEEE standard
limit (see Tables 34a, 34b, and 34c). The ICUT regis-
ters can be written to directly through the I
2
C interface
when CL_DISC (R17h[2]) is set to 0 (see Table 3). In
this case, the current limit of the port is configured
regardless of the status of the classification.
By setting the CL_DISC bit to 1, the MAX5965A/
MAX5965B automatically set the ICUT register based
upon the classification result of the port. See Table 3
and the Register Map and Description section.
High-Power Mode
When CL_DISC (R17h[2]) is set to 0, high-power mode
is configured by setting the ICUT bits to any combina-
tion other than 000, 110, or 111 (note that 000 is the
default value for the IEEE standard limit). See Table 3
and the Register Map and Description section.
Foldback Current
During startup and normal operation, an internal circuit
senses the voltage at OUT_ and reduces the current-
limit value when (V
OUT
_ - V
EE
) > 28V. The foldback
function helps to reduce the power dissipation on the
FET. The current limit eventually reduces down to 1/3 of
I
LIM
when (V
OUT
_ - V
EE
) > 48V (see Figure 3a). For
high-power mode, the foldback starts when (V
OUT
_ -
V
EE
) > 10V (see Figure 3b). In high-power mode, the
current limit (I
LIM
) is reduced down to minimum fold-
back current (V
TH_FB
/R
S
) when (V
OUT
_ - V
EE
) > 48V.
Figure 2. PGOOD_ Timing
PGOOD_
POK_
t
PGOOD
相关PDF资料 |
PDF描述 |
|---|---|
| MIC2214-SWBML TR | IC REG LDO 3.3V/1.6V 10MLF |
| MAX5929CEEG+T | IC HOT SWAP CTLR QUAD 24QSOP |
| GBM03DRKN | CONN EDGECARD 6POS DIP .156 SLD |
| VE-B6M-CY-B1 | CONVERTER MOD DC/DC 10V 50W |
| MAX5929DEEG+T | IC HOT SWAP CTLR QUAD 24QSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX5965BCAX+ | 制造商:Maxim Integrated Products 功能描述:- Rail/Tube |
| MAX5965BCAX+T | 制造商:Maxim Integrated Products 功能描述:HIGH-POWER, QUAD, MONOLITHIC, PSE CONTROLLERS FOR POWER OVER - Tape and Reel |
| MAX5965BEAX+ | 功能描述:热插拔功率分布 Quad PSE Controller for POE RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| MAX5965BEAX+T | 功能描述:热插拔功率分布 Quad PSE Controller for POE RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| MAX5965BUAX+ | 功能描述:热插拔功率分布 Quad PSE Controller for POE RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。