- 您现在的位置：买卖IC网 > Datasheet目录43 > MAX5978ETJ+ (Maxim Integrated)IC CTLR HOT-SWAP 32TQFN Datasheet资料下载
参数资料
| 型号： | MAX5978ETJ+ |
| 厂商： | Maxim Integrated |
| 文件页数： | 29/38页 |
| 文件大小： | 2412K |
| 描述： | IC CTLR HOT-SWAP 32TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 1 |
| 类型： | 热交换控制器 |
| 应用： | 刀峰式服务器，网络应用设备 |
| 内部开关： | 无 |
| 电流限制： | 可调 |
| 电源电压： | 2.7 V ~ 16 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-WFQFN 裸露焊盘 |
| 供应商设备封装： | 32-TQFN-EP（5x5） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页当前第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页
0 to 16V, Hot-Swap Controller with 10-Bit
Current, Voltage Monitor, and 4 LED Drivers
29
The contents of a buffer can be retrieved as a block read
of either fifty 10-bit values (spanning 2 bytes each) or of
50 high-order bytes, depending on the per-signal bit set-
tings of register cbufrd_hibyonly (see Table 42).
If the circular buffer contents are retrieved as 10-bit
data, the first byte read-out is the high-order 8 bits of the
10-bit sample, and the second byte read-out contains
the 2 least-significant bits (LSBs) of the sample. This is
repeated for each of the 50 samples in the buffer. Thus,
2 bytes must be read for each 10-bit sample retrieved.
Conversely, if the buffer contents are retrieved as 8-bit
data, then each byte read-out contains the 8 MSBs of
each successive sample. It is important to remember
that in 10-bit mode, 100 bytes must be read to extract the
entire buffer contents, but in 8-bit mode, only 50 bytes
must be read.
The circular buffer system has a user-programmable
stop delay that specifies a certain number of sample
cycles to continue recording to the buffer after a shut-
down occurs. This delay value is stored in register
cbuf_dly_stop[5:0] (see Table 43).
The default (reset) value of the buffer stop delay is
25 samples, which means that an equal number of
samples are stored in the buffer preceding and follow-
ing the moment of the shutdown event. The buffer stop
delay is analogous to an oscilloscope trigger delay
because it allows the device to record what happened
both immediately before and after a shutdown. In other
words, when the contents of a circular buffer are read
out of the device, the shutdown event is by default
located in the middle of the recorded data. The balance
of data before and after an event can be altered by writ-
ing a different value (between 0 and 50) to the buffer
stop-delay register.
Latched-Off Fault Management
In the event of an overcurrent, undervoltage, or overvolt-
age condition that results in the shutdown of the hot-
swap channel, the device remains latched off.
To restart the latched-off channel, the user must either
cycle power to the IN input, or toggle the ON pin, EN1
bit, or the EN2 bit.
Table 40. Circular Buffer Read Addresses
Table 41. Circular Buffer Control Register Format
Table 42. Circular Buffer Resolution Register Format
ADDRESS
NAME
DESCRIPTION
0x46
cbuf_ba_v
Base address for voltage buffer block read
0x47
cbuf_ba_i
Base address for current buffer block read
Description:
Circular buffer run-stop control register (per-buffer control: 1 = run, 0 = stop)
Register Title:
cbuf_chx_store
Register Address:
0x19
RESET
VALUE
R
R
R
R
R/W
R/W
R/W
R/W
Unused
Unused
Ch0_i_run
Ch0_v_run
0x0F
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Description:
Circular buffer read-out resolution: high-order byte only, or 8-2 split 10-bit data
(per-buffer control: 1 = high-order byte output, 0 = full-resolution 10-bit output)
Register Title:
cbufrd_hibyonly
Register Address:
0x3F
RESET
VALUE
R
R
R
R
R/W
R/W
R/W
R/W
Unused
Unused
i_res
v_res
0x0F
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
相关PDF资料 |
PDF描述 |
|---|---|
| MAX5981BETE+ | IC CTRLR PD IEEE 802.3AF 16TQFN |
| MAX5986AETE+ | IC POE SWITCH PSE 16TQFN |
| MAX6509CAZK/V+T | IC TEMP SWITCH RES-PROG 5TSOT |
| MAX6513TT075+T | IC TEMP SWITCH REMOTE 6-TDFN |
| MAX6581TG9A+ | IC TEMP SENSOR 8-CH PREC 24-TQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX5978ETJ+ | 功能描述:热插拔功率分布 0-16V Hot-Swap Controller RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| MAX5978ETJ+T | 功能描述:热插拔功率分布 0-16V Hot-Swap Controller RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| MAX5980EVKIT# | 功能描述:电源开关 IC - POE / LAN MAX5980 Eval Kit RoHS:否 制造商:Fairchild Semiconductor 开关数量:Single 开关配置:SPST 开启电阻（最大值）:7.3 Ohms 串话: 带宽: 开启时间（最大值）:13 ns 关闭时间（最大值）:20 ns 切换电压（最大）: 工作电源电压:8 V to 26 V 最大工作温度:+ 125 C 安装风格:Through Hole 封装 / 箱体:TO-220F-6 |
| MAX5980EVKIT+ | 功能描述:电源开关 IC - POE / LAN RoHS:否 制造商:Fairchild Semiconductor 开关数量:Single 开关配置:SPST 开启电阻（最大值）:7.3 Ohms 串话: 带宽: 开启时间（最大值）:13 ns 关闭时间（最大值）:20 ns 切换电压（最大）: 工作电源电压:8 V to 26 V 最大工作温度:+ 125 C 安装风格:Through Hole 封装 / 箱体:TO-220F-6 |
| MAX5980GTJ+ | 功能描述:电源开关 IC - POE / LAN 0-16V Hot-Swap Controller RoHS:否 制造商:Fairchild Semiconductor 开关数量:Single 开关配置:SPST 开启电阻（最大值）:7.3 Ohms 串话: 带宽: 开启时间（最大值）:13 ns 关闭时间（最大值）:20 ns 切换电压（最大）: 工作电源电压:8 V to 26 V 最大工作温度:+ 125 C 安装风格:Through Hole 封装 / 箱体:TO-220F-6 |
发布紧急采购，3分钟左右您将得到回复。