参数资料
型号: MAX5980EVKIT#
厂商: Maxim Integrated Products
文件页数: 22/49页
文件大小: 0K
描述: EVAL KIT MAX5980
标准包装: 1
系列: *
Quad, IEEE 802.3at/af PSE Controller
for Power-over-Ethernet
SDA/SDAIN
t BUF
t LOW
t SU, DAT
t HD, DAT
t SU, STA
t HD, STA
t SU, STO
SCL
t HIGH
t HD, STA
START CONDITION
t R
t F
REPEATED START CONDITION
STOP
START
Figure 5. Serial Interface Timing Details
Table 3. Programmable Device Address Settings
DEVICE ADDRES S
CONDITION
CONDITION
B7
0
B6
1
B5
0
B4
A3
B3
A2
B2
A1
B1
A0
Device Address (AD0)
The MAX5980 is programmable to 1 of 16 unique slave
device addresses. The three MSBs of the device address
are always [010]. The 4 LSBs of the device address are
programmable, and are formed by the states of the Slave
Address Inputs (A0, A1, A2, and A3; see Table 3). To
program the device address, connect A0, A1, A2, and
A3 to a combination of V DD (logical 1) and DGND (logi-
cal 0), and initiate a device reset.
I 2 C-Compatible Serial Interface
The device operates as a slave that sends and receives
data through an I 2 C-compatible, 2-wire or 3-wire inter-
face. The interface uses a serial-data input line (SDAIN),
a serial-data output line (SDAOUT), and a serial-clock line
(SCL) to achieve bidirectional communication between
master(s) and slave(s). A master (typically a microcon-
troller) initiates all data transfers to and from the device,
and generates the SCL clock that synchronizes the data
22
transfer. In most applications, connect the SDAIN and
the SDAOUT lines together to form the serial-data line
(SDA). Most of the figures shown label the bus as SDA.
Using the separate input and output data lines allows
optocoupling with the controller bus when an isolated
supply powers the microcontroller.
The device's SDAIN line operates as an input and
SDAOUT operates as an open-drain output. A pullup
resistor, typically 4.7k I , is required on SDAOUT (3-wire
mode) or SDA (2-wire mode). The SCL line operates only
as an input. A pullup resistor, typically 4.7k I , is required
on SCL if there are multiple masters, or if the master in
a single-master system has an open-drain SCL output.
Serial Addressing
Each transmission consists of a START condition sent by
a master, followed by the device's 7-bit slave address
plus R/W bit, a register address byte, 1 or more data
bytes, and finally a STOP condition.
相关PDF资料
PDF描述
MAX5982CEVKIT# EVAL KIT MAX5982C
MAX6397SATA+T IC SW OVERVOLT PROT 8-TDFN
MAX6496EVKIT+ KIT EVAL FOR MAX6496
MAX6651EVKIT EVAL KIT FOR MAX6651
MAX7325EVKIT+ KIT EVAL FOR MAX7325
相关代理商/技术参数
参数描述
MAX5980EVKIT# 功能描述:电源开关 IC - POE / LAN MAX5980 Eval Kit RoHS:否 制造商:Fairchild Semiconductor 开关数量:Single 开关配置:SPST 开启电阻(最大值):7.3 Ohms 串话: 带宽: 开启时间(最大值):13 ns 关闭时间(最大值):20 ns 切换电压(最大): 工作电源电压:8 V to 26 V 最大工作温度:+ 125 C 安装风格:Through Hole 封装 / 箱体:TO-220F-6
MAX5980EVKIT+ 功能描述:电源开关 IC - POE / LAN RoHS:否 制造商:Fairchild Semiconductor 开关数量:Single 开关配置:SPST 开启电阻(最大值):7.3 Ohms 串话: 带宽: 开启时间(最大值):13 ns 关闭时间(最大值):20 ns 切换电压(最大): 工作电源电压:8 V to 26 V 最大工作温度:+ 125 C 安装风格:Through Hole 封装 / 箱体:TO-220F-6
MAX5980GTJ+ 功能描述:电源开关 IC - POE / LAN 0-16V Hot-Swap Controller RoHS:否 制造商:Fairchild Semiconductor 开关数量:Single 开关配置:SPST 开启电阻(最大值):7.3 Ohms 串话: 带宽: 开启时间(最大值):13 ns 关闭时间(最大值):20 ns 切换电压(最大): 工作电源电压:8 V to 26 V 最大工作温度:+ 125 C 安装风格:Through Hole 封装 / 箱体:TO-220F-6
MAX5980GTJ+T 功能描述:电源开关 IC - POE / LAN 0-16V Hot-Swap Controller RoHS:否 制造商:Fairchild Semiconductor 开关数量:Single 开关配置:SPST 开启电阻(最大值):7.3 Ohms 串话: 带宽: 开启时间(最大值):13 ns 关闭时间(最大值):20 ns 切换电压(最大): 工作电源电压:8 V to 26 V 最大工作温度:+ 125 C 安装风格:Through Hole 封装 / 箱体:TO-220F-6
MAX5980UTJ+ 功能描述:电源开关 IC - POE / LAN 0-16V Hot-Swap Controller RoHS:否 制造商:Fairchild Semiconductor 开关数量:Single 开关配置:SPST 开启电阻(最大值):7.3 Ohms 串话: 带宽: 开启时间(最大值):13 ns 关闭时间(最大值):20 ns 切换电压(最大): 工作电源电压:8 V to 26 V 最大工作温度:+ 125 C 安装风格:Through Hole 封装 / 箱体:TO-220F-6