- 您现在的位置：买卖IC网 > PDF目录14390 > MAX630CSA+ (Maxim Integrated Products)IC REG BOOST 0.15A 8SOIC PDF资料下载
参数资料
| 型号： | MAX630CSA+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 7/14页 |
| 文件大小： | 0K |
| 描述： | IC REG BOOST 0.15A 8SOIC |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 100 |
| 类型： | 升压（升压） |
| 输出数： | 1 |
| 输入电压： | 2 V ~ 16.5 V |
| 频率 - 开关： | 40kHz |
| 电流 - 输出： | 150mA |
| 同步整流器： | 无 |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 包装： | 管件 |
| 供应商设备封装： | 8-SOIC |
CMOS Micropower Step-Up
Switching Regulator
Potted Toroidal Inductors
A typical 1mH, 0.82 Ω potted toroidal inductor (Dale TE-
3Q4TA) is 0.685in in diameter by 0.385in high and
mounts directly onto a PC board by its leads. Such
devices offer high efficiency and mounting ease, but at
a somewhat higher cost than molded inductors.
Ferrite Cores (Pot Cores)
Pot cores are very popular as switch-mode inductors
since they offer high performance and ease of design.
The coils are generally wound on a plastic bobbin,
which is then placed between two pot core sections. A
simple clip to hold the core sections together com-
pletes the inductor. Smaller pot cores mount directly
onto PC boards through the bobbin terminals. Cores
come in a wide variety of sizes, often with the center
posts ground down to provide an air gap. The gap pre-
vents saturation while accurately defining the induc-
tance per turn squared.
Pot cores are suitable for all DC-DC converters, but are
usually used in the higher power applications. They are
also useful for experimentation since it is easy to wind
coils onto the plastic bobbins.
Toroidal Cores
In volume production, the toroidal core offers high per-
formance, low size and weight, and low cost. They are,
however, slightly more difficult for prototyping, in that
manually winding turns onto a toroid is more tedious
than on the plastic bobbins used with pot cores.
Table 1. Coil and Core Manufacturers
Toroids are more efficient for a given size since the flux
is more evenly distributed than in a pot core, where the
effective core area differs between the post, side, top,
and bottom.
Since it is difficult to gap a toroid, manufacturers produce
toroids using a mixture of ferromagnetic powder (typically
iron or Mo-Permalloy powder) and a binder. The perme-
ability is controlled by varying the amount of binder,
which changes the effective gap between the ferromag-
netic particles. Mo-Permalloy powder (MPP) cores have
lower losses and are recommended for the highest effi-
ciency, while iron powder cores are lower cost.
Diodes
In most MAX630 circuits, the inductor current returns to
zero before L X turns on for the next output pulse. This
allows the use of slow turn-off diodes. On the other
hand, the diode current abruptly goes from zero to full
peak current each time L X switches off (Figure 1, D1).
To avoid excessive losses, the diode must therefore
have a fast turn-on time.
For low-power circuits with peak currents less than
100mA, signal diodes such as 1N4148s perform well.
For higher-current circuits, or for maximum efficiency at
low power, the 1N5817 series of Schottky diodes are
recommended. Although 1N4001s and other general-
purpose rectifiers are rated for high currents, they are
unacceptable because their slow turn-on time results in
excessive losses.
MANUFACTURER
MOLDED INDUCTORS
Dale
Nytronics
TRW
POTTED TOROIDAL INDUCTORS
Dale
TRW
Torotel Prod.
FERRITE CORES AND TOROIDS
Allen Bradley
Siemens
Magnetics
Stackpole
Magnetics
TYPICAL PART NUMBER
IHA-104
WEE-470
LL-500
TE-3Q4TA
MH-1
PT 53-18
T0451S100A
B64290-K38-X38
555130
57-3215
G-41408-25
DESCRIPTION
500μH, 0.5 Ω
470μH, 10 Ω
500μH, 0.75 Ω
1mH, 0.82 Ω
600μH, 1.9 Ω
500μH, 5 Ω
Tor. core, 500nH/T 2
Tor. core, 4μH/T 2
Tor. core, 53nH/T 2
Pot core, 14mm x 18mm
Pot core, 14 x 8, 250nH/T 2
Note:
This list does not constitute an endorsement by Maxim Integrated Products and is not intended to be a comprehensive list of
all manufacturers of these components.
_______________________________________________________________________________________
7
相关PDF资料 |
PDF描述 |
|---|---|
| MAX634CSA+ | IC REG INV FLYBK ADJ 0.15A 8SOIC |
| ECC43DRXI | CONN EDGECARD 86POS DIP .100 SLD |
| RCM28DRYH | CONN EDGECARD 56POS DIP .156 SLD |
| ESC22DRAN | CONN EDGECARD 44POS R/A .100 SLD |
| LQW15AN4N1B00D | INDUCTOR |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX630CSA+ | 功能描述:直流/直流开关调节器 CMOS uPower Step Up Switching Reg RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| MAX630CSA+T | 功能描述:直流/直流开关调节器 CMOS uPower Step Up Switching Reg RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| MAX630CSA-C70048 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| MAX630CSA-C71098 | 制造商:Maxim Integrated Products 功能描述:8 PINS N.SO PKG - Rail/Tube |
| MAX630CSA-T | 功能描述:直流/直流开关调节器 CMOS uPower Step Up Switching Reg RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
发布紧急采购，3分钟左右您将得到回复。