- 您现在的位置：买卖IC网 > PDF目录67802 > MAX669EUB+T (MAXIM INTEGRATED PRODUCTS INC) 1.8V to 28V Input, PWM Step-Up Controllers in µMAX PDF资料下载
参数资料
| 型号： | MAX669EUB+T |
| 厂商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分类： | 稳压器 |
| 英文描述： | 1.8V to 28V Input, PWM Step-Up Controllers in µMAX |
| 中文描述： | SWITCHING CONTROLLER, 575 kHz SWITCHING FREQ-MAX, PDSO10 |
| 封装： | COMPACT, UMAX-10 |
| 文件页数： | 17/18页 |
| 文件大小： | 289K |
| 代理商： | MAX669EUB+T |
Detailed Description
The MAX668/MAX669 current-mode PWM controllers
operate in a wide range of DC-DC conversion applica-
tions, including boost, SEPIC, flyback, and isolated out-
put configurations. Optimum conversion efficiency is
maintained over a wide range of loads by employing
both PWM operation and Maxim’s proprietary Idle
Mode control to minimize operating current at light
loads. Other features include shutdown, adjustable
internal operating frequency or synchronization to an
external clock, soft start, adjustable current limit, and a
wide (1.8V to 28V) input range.
MAX668 vs. MAX669 Differences
Differences between the MAX668 and MAX669 relate
to their use in bootstrapped or non-bootstrapped cir-
cuits (Table 1). The MAX668 operates with inputs as
low as 3V and can be connected in
either a boot-
strapped or non-bootstrapped (IC powered from input
supply or other source) configuration. When not boot-
strapped, the MAX668 has no restriction on output volt-
age. When bootstrapped, the output cannot exceed
28V.
The MAX669 is optimized for low input voltages (down
to 1.8V) and
requires bootstrapped operation (IC pow-
ered from VOUT) with output voltages no greater than
28V. Bootstrapping is required because the MAX669
does not have undervoltage lockout, but instead drives
EXT with an open-loop, 50% duty-cycle start-up oscilla-
tor when LDO is below 2.5V. It switches to closed-loop
operation only when LDO exceeds 2.5V. If a non-boot-
strapped connection is used with the MAX669 and if
VCC (the input voltage) remains below 2.7V, the output
voltage will soar above the regulation point. Table 2
recommends the appropriate device for each biasing
option.
MAX668/MAX669
1.8V to 28V Input, PWM Step-Up
Controllers in MAX
8
_______________________________________________________________________________________
NAME
FUNCTION
1
LDO
5V On-Chip Regulator Output. This regulator powers all internal circuitry including the EXT gate driver.
Bypass LDO to GND with a 1F or greater ceramic capacitor.
2
FREQ
Oscillator Frequency Set Input. A resistor from FREQ to GND sets the oscillator from 100kHz (ROSC =
500k
) to 500kHz (ROSC = 100k). fOSC = 5 x 1010 / ROSC. ROSC is still required if an external clock is used
at SYNC/SHDN (see the
SYNC/SHDN and FREQ Inputs section).
PIN
3
GND
Analog Ground
7
PGND
Power Ground for EXT Gate Driver and Negative Current-Sense Input
6
CS+
Positive Current-Sense Input. Connect a current-sense resistor, RCS, between CS+ and PGND.
5
FB
Feedback Input. The FB threshold is 1.25V.
4
REF
1.25V Reference Output. REF can source 50A. Bypass to GND with a 0.22F ceramic capacitor.
10
SYNC/
SHDN
Shutdown control and Synchronization Input. There are three operating modes:
SYNC/SHDN low: DC-DC off.
SYNC/SHDN high: DC-DC on with oscillator frequency set at FREQ by ROSC.
SYNC/SHDN clocked: DC-DC on with operating frequency set by SYNC clock input. DC-DC conversion
cycles initiate on rising edge of input clock.
9
VCC
Input Supply to On-Chip LDO Regulator. VCC accepts inputs up to 28V. Bypass to GND with a 0.1F ceramic
capacitor.
8
EXT
External MOSFET Gate-Driver Output. EXT swings from LDO to PGND.
Pin Description
Table 1. MAX668/MAX669 Comparison
MAX668
MAX669
VCC Input
Range
3V to 28V
1.8V to 28V
Operation
Bootstrapped or nonboot-
strapped. VCC can be con-
nected to input, output, or
other voltage source such as
a logic supply.
Must be boot-
strapped (VCC
must be connect-
ed to boosted out-
put voltage, VOUT).
UVLO
IC stops switching for LDO
below 2.5V.
No
Soft-Start
Yes
When LDO is
above 2.5V
FEATURE
相关PDF资料 |
PDF描述 |
|---|---|
| MAX6690MEE+T | 2°C Accurate Remote/Local Temperature Sensor with SMBus Serial Interface |
| MAX6692MSA+T | Precision SMBus-Compatible Remote/Local Temperature Sensors with Overtemperature Alarms |
| MAX6692MUA+ | Precision SMBus-Compatible Remote/Local Temperature Sensors with Overtemperature Alarms |
| MAX6692MUA+T | Precision SMBus-Compatible Remote/Local Temperature Sensors with Overtemperature Alarms |
| MAX6695AUB+ | Dual Remote/Local Temperature Sensors with SMBus Serial Interface |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX6700UT | 制造商:Maxim Integrated Products 功能描述:LOW-VOLTAGE HIGH-ACCURACY TRIPLE - Rail/Tube 制造商:Rochester Electronics LLC 功能描述: |
| MAX6700UT+ | 制造商:Maxim Integrated Products 功能描述:MAXIM MAX6700UT+ PROCESSOR SUPERVISORS - Tape and Reel 制造商:Maxim Integrated Products 功能描述:Maxim MAX6700UT+ Processor Supervisors 制造商:Maxim Integrated Products 功能描述:uP supervisory circuits, MAX6700UT+ |
| MAX6700UT+T | 功能描述:监控电路 Triple uPower Supervisor RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6700UT-T | 功能描述:监控电路 RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6701ALKA | 制造商:Maxim Integrated Products 功能描述:- Rail/Tube |
发布紧急采购，3分钟左右您将得到回复。