- 您现在的位置：买卖IC网 > PDF目录1845 > MAX6874ETJ+ (Maxim Integrated Products)IC SEQUENCE/SUPERVISOR 32TQFN PDF资料下载
参数资料
| 型号： | MAX6874ETJ+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 24/40页 |
| 文件大小： | 0K |
| 描述： | IC SEQUENCE/SUPERVISOR 32TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 43 |
| 类型： | 序列发生器 |
| 监视电压数目： | 6 |
| 输出： | 开路漏极，推挽式 |
| 复位： | 高有效/低有效 |
| 复位超时： | 可调节/可选择 |
| 电压 - 阀值： | 8 种可选阀值组合 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-WFQFN 裸露焊盘 |
| 供应商设备封装： | 32-TQFN-EP（5x5） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页当前第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页
EEPROM-Programmable, Hex/Quad,
Power-Supply Sequencers/Supervisors
Table 15. Programmable Output Active States
REGISTER
ADDRESS
3Ah
EEPROM
MEMORY
ADDRESS
803Ah
BIT
RANGE
[0]
[1]
[2]
[3]
[4]
[5]
[6]
[7]
DESCRIPTION
PO1 (MAX6874 only). 0 = active low, 1 = active high.
PO2 (MAX6874 only). 0 = active low, 1 = active high.
PO3 (MAX6874)/PO1 (MAX6875). 0 = active low, 1 = active high.
PO4 (MAX6874)/PO2 (MAX6875). 0 = active low, 1 = active high.
PO5 (MAX6874)/PO3 (MAX6875). 0 = active low, 1 = active high.
PO6 (MAX6874)/PO4 (MAX6875). 0 = active low, 1 = active high.
PO7 (MAX6874)/PO5 (MAX6875). 0 = active low, 1 = active high.
PO8 (MAX6874 only). 0 = active low, 1 = active high.
Table 16. PO_ Timeout Periods
REGISTER
ADDRESS
EEPROM
MEMORY
ADDRESS
BIT RANGE
AFFECTED OUTPUTS
MAX6874 MAX6875
DESCRIPTION
11h
8011h
[3:1]
PO1
—
15h
1Ch
23h
2Ah
31h
35h
39h
8015h
801Ch
8023h
802Ah
8031h
8035h
8039h
[3:1]
[4:2]
[4:2]
[3:1]
[3:1]
[3:1]
[3:1]
PO2
PO3
PO4
PO5
PO6
PO7
PO8
—
PO1
PO2
PO3
PO4
PO5
—
000 = 25μs
001 = 1.5625ms
010 = 6.25ms
011 = 25ms
100 = 50ms
101 = 200ms
110 = 400ms
111 = 1600ms
ured by the user). To configure the MAX6874/ MAX6875,
first apply an input voltage to IN1 or one of IN3–IN5
(MAX6874)/IN3–IN4 (MAX6875) (see the Powering the
MAX6874/MAX6875 section). V IN1 > +4V or one of
V IN3 –V IN5 > +2.7V, to ensure device operation. Next,
transmit data through the serial interface. Use the block
write protocol to quickly configure the device. Write to
the configuration registers first to ensure the device is
configured properly. After completing the setup proce-
dure, use the read word protocol to verify the data from
the configuration registers. Lastly, use the write word
protocol to write this data to the EEPROM registers. After
completing EEPROM register configuration, apply full
power to the system to begin normal operation. The non-
volatile EEPROM stores the latest configuration upon
removal of power. Write 0’s to all EEPROM registers to
clear the memory.
Software Reboot
A software reboot allows the user to restore the
EEPROM configuration to the volatile registers without
cycling the power supplies. Use the send byte com-
mand with data byte 88h to initiate a software reboot.
The 3.5ms (max) power-up delay also applies after a
software reboot.
SMBus/I 2 C-Compatible Serial Interface
The MAX6874/MAX6875 feature an I 2 C/SMBus-compati-
ble serial interface consisting of a serial data line (SDA)
and a serial clock line (SCL). SDA and SCL allow bidirec-
tional communication between the MAX6874/MAX6875
and the master device at clock rates up to 400kHz.
Figure 2 shows the interface timing diagram. The
MAX6874/MAX6875 are transmit/receive slave-only
devices, relying upon a master device to generate a
clock signal. The master device (typically a microcon-
troller) initiates data transfer on the bus and generates
SCL to permit that transfer.
24
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| MAX6876ETX+ | IC TRACKER/SUPERVISOR MON 36TQFN |
| MAX6879ETE+ | IC SEQUENCE/SUPERVISOR 16TQFN |
| MAX6881ETE+ | IC SEQUENCE/SUPERVISOR 16TQFN |
| MAX6884ETP+ | IC SUPERVISOR PWR SPL 20-TQFN |
| MAX6886ETP+T | IC SUPERVISOR HEX 20-TQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX6874ETJ+ | 功能描述:监控电路 EEPROM-Prog Hex Power-Sup Sequencer RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6874ETJ+T | 功能描述:监控电路 EEPROM-Prog Hex Power-Sup Sequencer RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6874ETJ-T | 功能描述:监控电路 RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6874TCC+ | 制造商:Maxim Integrated Products 功能描述: |
| MAX6875ETJ | 功能描述:监控电路 RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。