- 您现在的位置：买卖IC网 > PDF目录1845 > MAX6874ETJ+ (Maxim Integrated Products)IC SEQUENCE/SUPERVISOR 32TQFN PDF资料下载
参数资料
| 型号： | MAX6874ETJ+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 26/40页 |
| 文件大小： | 0K |
| 描述： | IC SEQUENCE/SUPERVISOR 32TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 43 |
| 类型： | 序列发生器 |
| 监视电压数目： | 6 |
| 输出： | 开路漏极，推挽式 |
| 复位： | 高有效/低有效 |
| 复位超时： | 可调节/可选择 |
| 电压 - 阀值： | 8 种可选阀值组合 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-WFQFN 裸露焊盘 |
| 供应商设备封装： | 32-TQFN-EP（5x5） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页当前第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页
EEPROM-Programmable, Hex/Quad,
Power-Supply Sequencers/Supervisors
Repeated START Conditions
A REPEATED START (SR) condition may indicate a
change of data direction on the bus. Such a change
occurs when a command word is required to initiate a
Slave Address
The MAX6874 slave address conforms to the following
table:
read operation (see Figure 7). SR may also be used
when the bus master is writing to several I 2 C devices
SA7
(MSB)
SA6
SA5
SA4
SA3
SA2
SA1
SA0
(LSB)
and does not want to relinquish control of the bus. The
MAX6874/MAX6875 serial interface supports continu-
ous write operations with or without an SR condition
1 0
X = Don’t care.
1
0
A1
A0
X
R/ W
separating them. Continuous read operations require
SR conditions because of the change in direction of
data flow.
The MAX6875 slave address conforms to the following
table:
Acknowledge
The acknowledge bit (ACK) is the 9th bit attached to any
8-bit data word. The receiving device always generates
SA7
(MSB)
1
SA6
0
SA5
1
SA4
0
SA3
0
SA2
A0
SA1
X
SA0
(LSB)
R/ W
an ACK. The MAX6874/MAX6875 generate an ACK
when receiving an address or data by pulling SDA low
during the 9th clock period (Figure 5). When transmitting
data, such as when the master device reads data back
from the MAX6874/MAX6875, the MAX6874/MAX6875
wait for the master device to generate an ACK.
Monitoring ACK allows for detection of unsuccessful data
transfers. An unsuccessful data transfer occurs if the
receiving device is busy or if a system fault has
occurred. In the event of an unsuccessful data transfer,
the bus master should reattempt communication at a
later time. The MAX6874/MAX6875 generate a NACK
after the slave address during a software reboot, while
writing to the EEPROM, or when receiving an illegal
memory address.
START
CONDITION
X = Don’t care.
SA7 through SA4 represent the standard interface
address (1010) for devices with EEPROM. SA3 and
SA2 correspond to the A1 and A0 address inputs of the
MAX6874/MAX6875 (hardwired as logic low or logic
high). A1 is internally set to 0 for the MAX6875. SA0 is a
read/write flag bit (0 = write, 1 = read).
The A0 and A1 address inputs allow up to four
MAX6874s or two MAX6875s to connect to one bus.
Connect A0 and A1 to GND or to the serial interface
power supply (see Figure 6).
CLOCK PULSE FOR ACKNOWLEDGE
SCL
1
2
8
9
SDA BY
TRANSMITTER
S
SDA BY
RECEIVER
Figure 5. Acknowledge
26
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| MAX6876ETX+ | IC TRACKER/SUPERVISOR MON 36TQFN |
| MAX6879ETE+ | IC SEQUENCE/SUPERVISOR 16TQFN |
| MAX6881ETE+ | IC SEQUENCE/SUPERVISOR 16TQFN |
| MAX6884ETP+ | IC SUPERVISOR PWR SPL 20-TQFN |
| MAX6886ETP+T | IC SUPERVISOR HEX 20-TQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX6874ETJ+ | 功能描述:监控电路 EEPROM-Prog Hex Power-Sup Sequencer RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6874ETJ+T | 功能描述:监控电路 EEPROM-Prog Hex Power-Sup Sequencer RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6874ETJ-T | 功能描述:监控电路 RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6874TCC+ | 制造商:Maxim Integrated Products 功能描述: |
| MAX6875ETJ | 功能描述:监控电路 RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。