- 您现在的位置：买卖IC网 > PDF目录18778 > MAX7033EUI+T (Maxim Integrated)IC RX 315MHZ/433MHZ ASK 28TSSOP PDF资料下载
参数资料
| 型号： | MAX7033EUI+T |
| 厂商： | Maxim Integrated |
| 文件页数： | 12/16页 |
| 文件大小： | 0K |
| 描述： | IC RX 315MHZ/433MHZ ASK 28TSSOP |
| 其它有关文件： | Automotive Product Guide |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 频率： | 315MHz，433MHz |
| 灵敏度： | -114dBm |
| 数据传输率 - 最大： | 33 kbps |
| 调制或协议： | ASK |
| 应用： | 汽车 RKE，遥控，无线传感器 |
| 电流 - 接收： | 5.2mA |
| 数据接口： | PCB，表面贴装 |
| 天线连接器： | PCB，表面贴装 |
| 电源电压： | 3 V ~ 3.6 V |
| 工作温度： | -40°C ~ 105°C |
| 封装/外壳： | 28-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 28-TSSOP |
| 包装： | 带卷 (TR) |
315MHz/433MHz ASK Superheterodyne
Receiver with AGC Lock
C 5 =
C 6 =
Intermediate Frequency and RSSI
The IF section presents a differential 330 Ω load to pro-
vide matching for the off-chip ceramic filter. The six
internal AC-coupled limiting amplifiers produce an
overall gain of approximately 65dB, with a bandpass-fil-
ter-type response centered near the 10.7MHz IF fre-
quency with a 3dB bandwidth of approximately 10MHz.
The RSSI circuit demodulates the IF by producing a DC
output proportional to the log of the IF signal level, with
a slope of approximately 14.2mV/dB (see the Typical
Operating Characteristics).
Applications Information
Crystal Oscillator
The crystal oscillator in the MAX7033 is designed to
present a capacitance of approximately 3pF between
the XTAL1 and XTAL2. If a crystal designed to oscillate
with a different load capacitance is used, the crystal is
pulled away from its stated operating frequency, intro-
ducing an error in the reference frequency. Crystals
designed to operate with higher differential load capac-
itance always pull the reference frequency higher. For
example, a 4.7547MHz crystal designed to operate
with a 10pF load capacitance oscillates at 4.7563MHz
with the MAX7033, causing the receiver to be tuned to
315.1MHz rather than 315.0MHz, an error of about
100kHz, or 320ppm.
In actuality, the oscillator pulls every crystal. The crys-
tal’s natural frequency is really below its specified fre-
quency, but when loaded with the specified load
capacitance, the crystal is pulled and oscillates at its
specified frequency. This pulling is already accounted
for in the specification of the load capacitance.
Additional pulling can be calculated if the electrical
It is possible to use an external reference oscillator in
place of a crystal to drive the VCO. AC-couple the exter-
nal oscillator to XTAL2 with a 1000pF capacitor. Drive
XTAL2 with a signal level of approximately -10dBm. AC-
couple XTAL1 to ground with a 1000pF capacitor.
Data Filter
The data filter is implemented as a 2nd-order lowpass
Sallen-Key filter. The pole locations are set by the com-
bination of two on-chip resistors and two external
capacitors. Adjusting the value of the external capaci-
tors changes the corner frequency to optimize for dif-
ferent data rates. The corner frequency should be set
to approximately 1.5 times the fastest expected data
rate from the transmitter. Keeping the corner frequency
near the data rate rejects any noise at higher frequen-
cies, resulting in an increase in receiver sensitivity.
The configuration shown in Figure 2 can create a
Butterworth or Bessel response. The Butterworth filter
offers a very flat amplitude response in the passband
and a rolloff rate of 40dB/decade for the two-pole filter.
The Bessel filter has a linear phase response, which
works well for filtering digital data. To calculate the
value of C5 and C6, use the following equations, along
with the coefficients in Table 2:
b
a ( 100 k )( π )( f C )
a
4 ( 100 k )( π )( f C )
where f C is the desired 3dB corner frequency.
Table 2. Coefficents to Calculate C5 and C6
parameters of the crystal are known. The frequency
pulling is given by:
FILTER TYPE
Butterworth (Q = 0.707)
a
1.414
b
1.000
C M ? 1 1 ?
? C
2 ? CASE + C LOAD C CASE + C SPEC ? ?
f P =
-
× 10 6
Bessel (Q = 0.577)
1.3617
0.618
where:
f P is the amount the crystal frequency pulled in ppm.
C M is the motional capacitance of the crystal.
MAX7033
R DF2
100k Ω
RSSI
R DF1
100k Ω
C CASE is the case capacitance.
C SPEC is the specified load capacitance.
C LOAD is the actual load capacitance.
19
DFO
C6
21
OPP
C5
22
DFFB
When the crystal is loaded as specified, i.e., C LOAD =
C SPEC , the frequency pulling equals zero.
Figure 2. Sallen-Key Lowpass Data Filter
12
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| EKMB1203113 | SENSOR MOTION PIR 12M RANGE WHT |
| EKMB1203112 | SENSOR MOTION PIR 12M RANGE BLK |
| MAX2120CTI+ | IC TUNER DIR-CONV DVB-S 28TQFN |
| EKMB1201111 | SENSOR MOTION PIR DIGITAL WHITE |
| MAX2120CTI+T | IC TUNER DIR-CONV DVB-S 28TQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX7033EVKIT-315 | 功能描述:射频开发工具 MAX7033 Eval Kit RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
| MAX7033EVKIT-433 | 功能描述:射频开发工具 MAX7033 Eval Kit RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
| MAX7034 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:315MHz/434MHz ASK Superheterodyne Receiver |
| MAX7034_09 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:315MHz/434MHz ASK Superheterodyne Receiver |
| MAX7034_11 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:315MHz/434MHz ASK Superheterodyne Receiver 250μs Startup Time |
发布紧急采购，3分钟左右您将得到回复。