- 您现在的位置：买卖IC网 > Datasheet目录341 > MAX7302ATE+ (Maxim Integrated)IC LED DRIVER LINEAR 16-TQFN Datasheet资料下载
参数资料
| 型号： | MAX7302ATE+ |
| 厂商： | Maxim Integrated |
| 文件页数： | 14/30页 |
| 文件大小： | 0K |
| 描述： | IC LED DRIVER LINEAR 16-TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 100 |
| 拓扑： | 开路漏极，PWM |
| 输出数： | 9 |
| 内部驱动器： | 是 |
| 类型 - 主要： | 背光，LED 闪烁器 |
| 类型 - 次要： | 白色 LED |
| 频率： | 1MHz |
| 电源电压： | 1.62 V ~ 3.6 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-WFQFN 裸露焊盘 |
| 供应商设备封装： | 16-TQFN（3x3） |
| 包装： | 管件 |
| 工作温度： | -40°C ~ 125°C |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页当前第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页
SMBus/I 2 C Interfaced 9-Port,
Level-Translating GPIO and LED Driver with CLA
INT Output
Port P1 can be configured as a latching interrupt out-
put, INT , that flags any transients on any combination of
selected ports configured as inputs. Configurable logic
gate outputs can also be monitored as readback inputs
with the same options as normal I/O port inputs. Any
transitions occurring at the selected inputs assert INT
low to alert the host processor of data changes at the
selected inputs. Reset INT by reading any ports I/O
registers (0x01 to 0x09).
Standby Mode
Upon power-up, the MAX7302 enters standby mode
when the serial interface is idle. If any of the PWM
intensity control, blink, or debounce features are used,
the operating current rises because the internal PWM
oscillator is running and toggling counters. When using
OSCIN to override the internal oscillator, the operating
current varies according to the frequency at OSCIN.
When the serial interface is active, the operating cur-
rent also increases because the MAX7302, like all I 2 C
slaves, has to monitor every transmission. The bus
timeout and debounce circuits use the internal oscilla-
tor even if OSCIN is selected.
Internal Oscillator and OSCIN/OSCOUT
External Clock Options
The MAX7302 contains an internal 32kHz oscillator. The
MAX7302 always uses the internal oscillator for bus
timeout and for debounce timing (when enabled). It is
used by default to generate PWM and blink timing. The
internal oscillator only runs when the clock output
OSCOUT is needed to keep the operating current as
low as possible.
The MAX7302 can use an external clock source instead
of the internal oscillator for the PWM and blink timing.
The external clock can range from DC to 1MHz, and it
connects to the P2/OSCIN port. The P3/OSCOUT port
provides a buffered and level-shifted output of the inter-
nal oscillator or external clock to drive other devices.
Select the P2/OSCIN and P3/OSCOUT port options
using the device configuration register 0x67 bits D2
and D3 (see Table 4).
The P2/OSCIN port is overvoltage protected to supply
voltage V LA , so the external clock can exceed V DD if
V LA is greater than V DD . The port P2 register (see
Tables 2 and 6) sets the P2/OSCIN logic threshold
(30%/70%) to either the V DD supply or the V LA .
Use OSCOUT or an external clock source to cascade
up to four MAX7302s per master for applications requir-
ing additional ports. To synchronize the blink action
across multiple MAX7302s (see Figures 4 and 5), use
OSCOUT from one MAX7302 to drive OSCIN of the
other MAX7302s. This process ensures the same blink
frequency of all the devices, but also make sure to syn-
chronize the blink phase. The blink timing of multiple
MAX7302s is synchronous at the instant of power-up
because the blink and PWM counters clear by each
MAX7302’s internal reset circuit, and by default the
MAX7302s’ internal oscillators are off upon power-up.
Ensure that the blink phase of all the devices remains
synchronized by programming the OSCIN and
OSCOUT functionality before programming any feature
that causes a MAX7302’s internal oscillator to operate
(blink, PWM, bus timeout, or key debounce). Configure
the RST input to reset the internal timing counters used
for PWM and blink by setting bit D1 of device configu-
ration register 0x26 (see Table 3).
PWM and Blink Timing
The MAX7302 divides the 32kHz nominal internal oscilla-
tor OSC or external clock source OSCIN frequency by 32
to provide a nominal 1kHz PWM frequency. Use the reset
MAX7302
P3/OSCOUT
MAX7302
P2/OSCIN
MAX7302
MAX7302
P2/OSCIN
MAX7302
MAX7302
P3/OSCOUT
P2/OSCIN
P3/OSCOUT
P2/OSCIN
Figure 4. Synchronizing Multiple MAX7302s (Internal Oscillator)
14
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| MAX7307AUB+T | IC LED DRIVER LINEAR 10-UMAX |
| MAX831EVKIT-SO | EVAL KIT FOR MAX831 |
| MAX8513EVKIT | EVAL KIT FOR MAX8513 |
| MAX8552EUB+ | IC DRIVER MOSFET HS 10-UMAX |
| MAX8595XETA+T | IC LED DRIVR WHITE BCKLGT 8-TDFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX7302ATE/GH9 | 制造商:Maxim Integrated Products 功能描述:LEVEL-TRANSLATING GPIO AND LED DRIVER WITH CLA - Rail/Tube |
| MAX7302ATE+ | 功能描述:外围驱动器与原件 - PCI 9-Port Level-Trans GPIO & LED Driver RoHS:否 制造商:PLX Technology 工作电源电压: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:FCBGA-1156 封装:Tray |
| MAX7302ATE+T | 功能描述:外围驱动器与原件 - PCI 9-Port Level-Trans GPIO & LED Driver RoHS:否 制造商:PLX Technology 工作电源电压: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:FCBGA-1156 封装:Tray |
| MAX7302EVKIT+ | 制造商:Maxim Integrated Products 功能描述:MAX7302 EVAL KIT - Boxed Product (Development Kits) |
| MAX7304 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:I2C-Interfaced 16-Port, Level-Translating GPIO and LED Driver with High Level of Integrated |
发布紧急采购，3分钟左右您将得到回复。