- 您现在的位置：买卖IC网 > Datasheet目录341 > MAX7302ATE+ (Maxim Integrated)IC LED DRIVER LINEAR 16-TQFN Datasheet资料下载
参数资料
| 型号： | MAX7302ATE+ |
| 厂商： | Maxim Integrated |
| 文件页数： | 25/30页 |
| 文件大小： | 0K |
| 描述： | IC LED DRIVER LINEAR 16-TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 100 |
| 拓扑： | 开路漏极，PWM |
| 输出数： | 9 |
| 内部驱动器： | 是 |
| 类型 - 主要： | 背光，LED 闪烁器 |
| 类型 - 次要： | 白色 LED |
| 频率： | 1MHz |
| 电源电压： | 1.62 V ~ 3.6 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-WFQFN 裸露焊盘 |
| 供应商设备封装： | 16-TQFN（3x3） |
| 包装： | 管件 |
| 工作温度： | -40°C ~ 125°C |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页当前第25页第26页第27页第28页第29页第30页
SMBus/I 2 C Interfaced 9-Port,
Level-Translating GPIO and LED Driver with CLA
Applications Information
Hot Insertion
Serial interfaces SDA, SCL, and AD0 remain high
impedance with up to 6V asserted on them when the
MAX7302 is powered down (V DD = 0V) independent of
the voltages on the port supply V LA . When V DD = 0V, or
if V DD falls below the MAX7302’s reset threshold, all I/O
ports become high impedance. The ports remain high
impedance to signals between 0V and the port supply
V LA . If a signal outside this range is applied to a port,
the port’s protection diodes clamp the input signal to
V LA or 0V, as appropriate. If supply V LA is lower than
the input signal, the port pulls up V LA and the protec-
tion diode effectively powers any load on V LA from the
input signal. This behavior is safe if the current through
each protection diode is limited to 10mA.
If it is important that I/O ports remain high impedance
when all the supplies are powered down, including the
port supply V LA , then ensure that there is no direct or
parasitic path for MAX7302 input signals to drive current
into either the regulator providing V LA or other circuits
powered from V LA . One simple way to achieve this is
with a series small-signal Schottky diode, such as the
BAT54, between the port supply and the V LA input.
Output Level Translation
The open-drain output configuration of the ports allows
them to level translate the outputs to lower (but not
higher) voltages than the V LA supply. An external
pullup resistor converts the high-impedance, logic-high
condition to a positive voltage level. Connect the resis-
tor to any voltage up to V LA . For interfacing CMOS
inputs, a pullup resistor value of 220k Ω is a good start-
ing point. Use a lower resistance to improve noise
immunity, in applications where power consumption is
less critical, or where a faster rise time is needed for a
given capacitive load.
Driving LED Loads
When driving LEDs, use a resistor in series with the
LED to limit the LED current to no more than 25mA.
Choose the resistor value according to the following
formula:
V SUPPLY is the supply voltage used to drive the
LED (V)
V LED is the forward voltage of the LED (V)
V OL is the output low voltage of the MAX7302
when sinking I LED (V)
I LED is the desired operating current of the LED (A).
For example, to operate a 2.2V red LED at 20mA from a
5V supply, R LED = (5 - 2.2 - 0.8) / 0.020 = 100 Ω .
Driving Load Currents Higher than 25mA
The MAX7302 can sink current from loads drawing
more than 25mA by sharing the load across multiple
ports configured as open-drain outputs. Use at least
one output per 25mA of load current; for example, drive
a 90mA white LED with four ports.
The register structure of the MAX7302 allows only one
port to be manipulated at a time. Do not connect ports
directly in parallel because multiple ports cannot be
switched high or low at the same time, which is neces-
sary to share a load safely. Multiple ports can drive
high-current LEDs because each port can use its own
external current-limiting resistor to set that port’s cur-
rent through the LED.
The exceptions to this paralleling rule are the four ports,
P2–P5, and the four ports, P6–P9. These groups of four
ports can be programmed simultaneously through the
pseudoregisters 0x3C and 0x3D, respectively. A write
access to 0x3C writes the same data to registers 0x02
through 0x05. A write access to 0x3D writes the same
data to registers 0x06 through 0x09. Either of these
groups of four ports can be paralleled to drive a load
up to 100mA.
Power-Supply Considerations
The MAX7302 operates with a V DD power-supply voltage
of 1.62V to 3.6V. Bypass V DD to GND with a 0.047μF
capacitor as close as possible to the device. The port
supply V LA is connected to a supply voltage between
1.62V to 5.5V and bypassed with a 0.1μF capacitor as
close as possible to the device. The V DD supply and port
supply are independent and can be connected to differ-
ent voltages or the same supply as required.
where:
R LED = (V SUPPLY - V LED - V OL ) / I LED
Power supplies V DD and V LA can be sequenced in
either order or together.
R LED is the resistance of the resistor in series with
the LED ( Ω )
______________________________________________________________________________________
25
相关PDF资料 |
PDF描述 |
|---|---|
| MAX7307AUB+T | IC LED DRIVER LINEAR 10-UMAX |
| MAX831EVKIT-SO | EVAL KIT FOR MAX831 |
| MAX8513EVKIT | EVAL KIT FOR MAX8513 |
| MAX8552EUB+ | IC DRIVER MOSFET HS 10-UMAX |
| MAX8595XETA+T | IC LED DRIVR WHITE BCKLGT 8-TDFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX7302ATE/GH9 | 制造商:Maxim Integrated Products 功能描述:LEVEL-TRANSLATING GPIO AND LED DRIVER WITH CLA - Rail/Tube |
| MAX7302ATE+ | 功能描述:外围驱动器与原件 - PCI 9-Port Level-Trans GPIO & LED Driver RoHS:否 制造商:PLX Technology 工作电源电压: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:FCBGA-1156 封装:Tray |
| MAX7302ATE+T | 功能描述:外围驱动器与原件 - PCI 9-Port Level-Trans GPIO & LED Driver RoHS:否 制造商:PLX Technology 工作电源电压: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:FCBGA-1156 封装:Tray |
| MAX7302EVKIT+ | 制造商:Maxim Integrated Products 功能描述:MAX7302 EVAL KIT - Boxed Product (Development Kits) |
| MAX7304 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:I2C-Interfaced 16-Port, Level-Translating GPIO and LED Driver with High Level of Integrated |
发布紧急采购，3分钟左右您将得到回复。