- 您现在的位置：买卖IC网 > PDF目录10618 > MAX7456EUI+ (Maxim Integrated Products)IC ON-SCREEN DISPLAY 28-TSSOP PDF资料下载
参数资料
| 型号： | MAX7456EUI+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 32/44页 |
| 文件大小： | 0K |
| 描述： | IC ON-SCREEN DISPLAY 28-TSSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 50 |
| 类型： | OSD（屏幕显示）视频发生器 |
| 应用： | 安全系统，视频路由 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-SOIC（0.173"，4.40mm 宽）裸露焊盘 |
| 供应商设备封装： | 28-TSSOP 裸露焊盘 |
| 包装： | 管件 |
| 产品目录页面： | 1424 (CN2011-ZH PDF) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页当前第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页
Single-Channel Monochrome On-Screen
Display with Integrated EEPROM
Applications Information
Character-Memory Operation
Only whole characters (54 bytes of pixel data) can be
written to or read from the NVM character memory at one
time. This is done through the (64 byte) shadow RAM
(see Figure 13). The shadow RAM is accessed by the
SPI port one byte at a time. The shadow RAM is written
to and read from the NVM by a single SPI command.
Steps for Writing Character Bytes
into the NVM Character Memory
Writing a new character:
1) Write VM0[3] = 0 to disable the OSD image display.
2) Write CMAH[7:0] = xxH to select the character
(0–255) to be written (Figures 10 and 13).
3) Write CMAL[7:0] = xxH to select the 4-pixel byte
(0–63) in the character to be written (Figures 10 and
13).
4) Write CMDI[7:0] = xxH to set the pixel values of the
selected part of the character (Figures 11 and 13).
5) Repeat steps 3 and 4 until all 54 bytes of the char-
acter data are loaded into the shadow RAM.
6) Write CMM[7:0] = 1010xxxx to write to the NVM
array from the shadow RAM (Figure 13). The char-
acter memory is busy for approximately 12ms dur-
ing this operation. STAT[5] can be read to verify that
the NVM writing process is complete.
7) Write VM0[3] = 1 to enable the OSD image display.
Modifying an existing character:
1) Write VM0[3] = 0 to disable the OSD image display.
2) Write CMAH[7:0] = xxH to select the character
(0–255) to be modified (Figures 10 and 13).
3) Write CMM[7:0] = 0101xxxx to read character data
from the NVM to the shadow RAM (Figure 13).
4) Write CMAL[7:0] = xxH to select the 4-pixel byte
(0–63) in the character to be modified (Figures 10
and 13).
5) Read CMDO[7:0] = xxH to read the byte of 4-pixel
data to be modified (Figures 11 and 13).
6) Modify the byte of 4-pixel data as desired.
7) Write CMDI[7:0] = xxH to write the modified byte of
4-pixel data back to the shadow RAM (Figures 11
and 13).
8) Repeat steps 4 through 7 as needed until all pixels
have been loaded into the shadow RAM.
9) Write CMM[7:0] = 1010xxxx to write the shadow
RAM data to the NVM (Figure 13). The character
memory is busy for typically 12ms during this oper-
ation. STAT[5] can be read to verify that the NVM
writing process is complete.
10) Write VM0[3] =1 to enable the OSD image display.
Steps for Reading Character
Bytes from Character Memory
1) Write VM0[3] = 0 to disable the OSD image.
2) Write CMAH[7:0] = xxH to select the character
(0–255) to be read (Figures 10 and 13).
3) Write CMM[7:0] = 0101xxxx to read the character
data from the NVM to the shadow RAM (Figure 13).
4) Write CMAL[7:0] = xxH to select the 4-pixel byte
(0–63) in the character to be read (Figures 10 and 13).
5) Read CMDO[7:0] = xxH to read the selected 4-pixel
byte of data (Figures 11 and 13).
6) Repeat steps 4 and 5 to read other bytes of 4-pixel
data.
7) Write VM0[3] = 1 to enable the OSD image display.
Display-Memory Operation
The following two steps enable viewing of the OSD
image. These steps are not required to read from or
write to the display memory:
1) Write VM0[3] = 1 to enable the display of the OSD
image.
2) Write OSDBL[4] = 0 to enable automatic OSD black
level control. This ensures the correct OSD image
brightness. This register contains 4 factory-preset
bits [3:0] that must not be changed. Therefore,
when changing bit 4, first read OSDBL[7:0], modify
bit 4, and then write back the updated byte.
Steps for Clearing Display Memory
Write DMM[2] = 1 to start the clear display-memory
operation. This operation typically takes 20s. The
Display Memory Mode register cannot be written to
again until the clear operation is complete. DMM[2] is
automatically reset to zero upon completion.
Steps for Writing to
Display Memory in 8-Bit Mode
The 8-bit operation mode provides maximum flexibility
when writing characters to the display memory. This
mode enables writing individual Character Attribute
bytes for each character (see Table 5). This mode is
distinct from the 16-bit operation mode where the
Character Attribute byte is automatically copied from
DMM[5:3] when a character is written (Figure 19).
Write DMM[6] = 1 to select the 8-bit operation mode.
MAX7456
38
Maxim Integrated
相关PDF资料 |
PDF描述 |
|---|---|
| MAX242EPN+ | IC TXRX RS232 5V 18-DIP |
| MAX3815CCM+D | IC EQUALIZER VIDEO 48-TQFP |
| MAX9135GHJ+ | IC SW LVDS CROSSBAR 32TQFP-EP |
| MAX242EWN+ | IC TXRX RS232 5V 18-SOIC |
| MAX9134GHJ+ | IC SW LVDS CROSSBAR 32TQFP-EP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX7456EUI/GH9 | 制造商:Maxim Integrated Products 功能描述:SINGLE-CHANNEL MONOCHROME ON-SCREEN DISPLAY - Rail/Tube |
| MAX7456EUI+ | 功能描述:视频 IC Monochrome On Scrn Display Generator RoHS:否 制造商:Fairchild Semiconductor 工作电源电压:5 V 电源电流:80 mA 最大工作温度:+ 85 C 封装 / 箱体:TSSOP-28 封装:Reel |
| MAX7456EUI+T | 功能描述:视频 IC Monochrome On Scrn Display Generator RoHS:否 制造商:Fairchild Semiconductor 工作电源电压:5 V 电源电流:80 mA 最大工作温度:+ 85 C 封装 / 箱体:TSSOP-28 封装:Reel |
| MAX7456EUI+W | 制造商:Maxim Integrated Products 功能描述:- Rail/Tube |
| MAX7456EVKIT | 功能描述:显示开发工具 RoHS:否 制造商:4D Systems 产品:4Display Shields 工具用于评估:?OLED-160-G1, ?OLED-160-G2 接口类型:Serial 工作电源电压:5 V |
发布紧急采购，3分钟左右您将得到回复。