- 您现在的位置：买卖IC网 > PDF目录22320 > MAX8513EEI+ (Maxim Integrated)IC REG TRPL BUCK/LINEAR 28QSOP PDF资料下载
参数资料
| 型号： | MAX8513EEI+ |
| 厂商： | Maxim Integrated |
| 文件页数： | 18/35页 |
| 文件大小： | 0K |
| 描述： | IC REG TRPL BUCK/LINEAR 28QSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 50 |
| 拓扑： | 降压（降压）（1），线性（LDO）（2） |
| 功能： | 任何功能 |
| 输出数： | 3 |
| 频率 - 开关： | 250kHz ~ 1.5MHz |
| 电压/电流 - 输出 1： | 控制器 |
| 电压/电流 - 输出 2： | 控制器 |
| 电压/电流 - 输出 3： | 控制器 |
| 带 LED 驱动器： | 无 |
| 带监控器： | 无 |
| 带序列发生器： | 无 |
| 电源电压： | 4.5 V ~ 28 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 28-QSOP |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页当前第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页
Wide-Input, High-Frequency, Triple-Output Supplies
with Voltage Monitor and Power-On Reset
Thermal-Overload Protection
Thermal-overload protection limits the total power dissi-
pation in the MAX8513/MAX8514. When the junction
temperature exceeds T J = +170°C, a thermal sensor
shuts down the device, forcing DL and DH low and
value allows for a smaller inductor but results in higher
losses and higher output ripple. A good compromise
between size and efficiency is a 30% LIR. Once all of
the parameters are chosen, the inductor value is deter-
mined as follows:
allowing the IC to cool. The thermal sensor turns the part
on again after the junction temperature cools by 25°C,
resulting in a pulsed output during continuous thermal-
overload conditions. During a thermal event, the main
L =
V OUT 1 × ( V IN - V OUT 1 )
V IN × f S × I OUT 1 _ MAX × LIR
R 1 = R 2 × ? OUT 1 - 1 ?
step-down converter and the linear regulators are turned
off, POR and PFO go low, and soft-start is reset.
Design Procedure
OUT1 Voltage Setting
The output voltage is set by a resistive-divider network
from OUT1 to FB1 to GND (see R1 and R2 in the
Typical Applications Circuits ). Select R2 between 5k ?
and 15k ? . Then R1 can be calculated by:
? V ?
? 1 . 25 V ?
Input Power-Fail Setting
The PFI input can monitor V IN to determine if it is falling.
When the voltage at PFI crosses 1.22V, the output
( PFO ) goes low. The input voltage value at the PFI trip
where V OUT1 is the main switching regulator output and
f S is the switching frequency.
Choose a standard value close to the calculated value.
The exact inductor value is not critical and can be
adjusted to make tradeoffs between size, cost, and effi-
ciency. Lower inductor values minimize size and cost,
but also increase the output ripple and reduce the effi-
ciency due to higher peak currents. On the other hand,
higher inductor values increase efficiency, but eventual-
ly resistive losses due to extra turns of wire exceed the
benefit gained from lower AC current levels. Find a low-
loss inductor with the lowest possible DC resistance that
fits the allotted dimensions. Ferrite cores are often the
best choice, although powdered iron is inexpensive and
can work well up to 300kHz. The chosen inductor’s satu-
ration current rating must exceed the peak inductor cur-
rent as calculated below:
threshold, V PFI , is set by a resistive-divider network
from IN to PFI to GND (see the Typical Applications
Circuits ). Select R11, the resistor from PFI to GND
I PEAK = I OUT 1 _ MAX +
( V IN - V OUT1 ) × V OUT 1
2 × L × f S × V IN
between 10k ? and 40k ? . Then R10, the resistor from
PFI to IN, is calculated by:
This peak value should be smaller than the value set at
ILIM when V OUT1 is at its nominal regulated voltage (see
R 10 = R 11 × ?
- 1 ?
? V PFI
? 1 . 22 V
?
?
the Current Limit and Current-Limit Setting sections).
In applications where a multiple winding inductor (cou-
pled inductor) is used to generate the supply voltages
Switching-Frequency Setting
The resistor connected from FREQ to GND, R FREQ (R7
in the Typical Applications Circuits ), sets the switching
frequency, f S , as shown by the equation below:
for the LDOs, the inductance value calculated above is
for the winding connected to the DC-DC step-down
(primary windings) inductance. The inductance seen
from the other windings (secondary windings) is pro-
portional to the square of the turns ratio with respect to
f S =
15 × 10 9
R FREQ
Hz × ?
the primary winding.
The turns ratio is important since it sets the LDOs’ sup-
ply voltage values. The voltage generated by the sec-
where R FREQ is in ohms.
ondary winding (V SEC ) together with the rectifier diode
and output capacitor is calculated as follows:
) × ? ? nn 2 ? ? - V D2
Inductor Value
There are several parameters that must be examined
when determining which inductor to use: input voltage,
output voltage, load current, switching frequency, and
V SEC = ( V OUT 1 + V Q 2
? ?
1
LIR. LIR is the ratio of peak-to-peak inductor ripple cur-
rent to the maximum DC load current. A higher LIR
where V Q2 and V D2 are the voltage drops across the
low-side MOSFET on the primary side and the rectifier
18
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| EEC30DREI-S13 | CONN EDGECARD 60POS .100 EXTEND |
| V300C3V3H50B2 | CONVERTER MOD DC/DC 3.3V 50W |
| RSC06DRYI | CONN EDGECARD 12POS DIP .100 SLD |
| RMC06DRYI | CONN EDGECARD 12POS DIP .100 SLD |
| RBC13DRYI | CONN EDGECARD 26POS .100 EXTEND |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX8513EEI+ | 功能描述:DC/DC 开关控制器 Triple-Output Supply RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX8513EEI+T | 功能描述:DC/DC 开关控制器 Triple-Output Supply RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX8513EEI-T | 功能描述:DC/DC 开关控制器 RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX8513EVKIT | 功能描述:电源管理IC开发工具 RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| MAX8514AEI | 功能描述:DC/DC 开关控制器 RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
发布紧急采购，3分钟左右您将得到回复。