- 您现在的位置：买卖IC网 > PDF目录22320 > MAX8513EEI+ (Maxim Integrated)IC REG TRPL BUCK/LINEAR 28QSOP PDF资料下载
参数资料
| 型号： | MAX8513EEI+ |
| 厂商： | Maxim Integrated |
| 文件页数： | 29/35页 |
| 文件大小： | 0K |
| 描述： | IC REG TRPL BUCK/LINEAR 28QSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 50 |
| 拓扑： | 降压（降压）（1），线性（LDO）（2） |
| 功能： | 任何功能 |
| 输出数： | 3 |
| 频率 - 开关： | 250kHz ~ 1.5MHz |
| 电压/电流 - 输出 1： | 控制器 |
| 电压/电流 - 输出 2： | 控制器 |
| 电压/电流 - 输出 3： | 控制器 |
| 带 LED 驱动器： | 无 |
| 带监控器： | 无 |
| 带序列发生器： | 无 |
| 电源电压： | 4.5 V ~ 28 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 28-QSOP |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页当前第29页第30页第31页第32页第33页第34页第35页
Wide-Input, High-Frequency, Triple-Output Supplies
with Voltage Monitor and Power-On Reset
the package’s power dissipation could limit the useable
maximum input-to-output voltage differential.
The maximum power-dissipation capability of the tran-
sistor’s package and mounting must allow the actual
power dissipation in the device without exceeding the
maximum junction temperature. The power dissipated
equals the maximum load current multiplied by the
maximum input-to-output voltage differential.
When the MAX8513/MAX8514 are disabled, R26 dis-
charges C7.
OUT3P Voltage Selection (PNP)
The MAX8513 positive linear-regulator output voltage,
V OUT3P , is set with a resistive-divider from OUT3P to
FB3P to GND. First, select R14 resistance value (below
1k ? ). Then, solve for R13 so:
transistor’s specifications, the base-emitter resistor,
and the output capacitor determine the loop stability.
The total DC loop gain (A V ) is the product of the gains
of the internal transconductance amplifier, the gain
from base to collector of the pass transistor (Q4 in the
Typical Applications Circuits ), and the gain of the feed-
back divider.
The transconductance amplifier regulates the output
voltage by controlling the pass transistor’s base cur-
rent. Its DC gain is approximately:
G C 3 _ × R IN || R 12
where G C3_ is typically 0.6S (OUT3P) and 0.36S
(OUT3N), R IN is the input resistance of Q4, and can be
calculated by:
R 13 = R 14 ? OUT 3 P -1 ?
R IN = ?
? V ?
? 0 . 8 V ?
? 26 mV
? I OUT 3 _
?
β ?
?
where V OUT3P can range from +0.8V to +27V.
OUT3N Voltage Selection (NPN)
The DC gain for the transistor (Q4), including the feed-
back divider, is approximately:
The MAX8514’s negative linear-regulator output volt-
age, V OUT3N , is a negative regulated voltage devel-
oped through the pass transistor Q4 (MAX8514 Typical
A Q 4 P =
V REF
VT
for OUT 3 P or
Applications Circuits ). A resistive-divider from OUT3N
to FB3N to V REF3N forces V FB3N to regulate to 0V.
Calculate V OUT3N by first selecting R14 the resistor
A Q 4 N =
V OUT 3 N × V REF 3 N
( V REF 3 N - V OUT 3 N ) × V T
from V REF3N to FB3N to be below 5k ? , where V REF3N
is any positive voltage (usually V OUT1 ). R13 is then cal-
culated by:
V T is the thermal voltage for the transistor (typically 26mV
at T A = +27 ° C). The total DC loop gain for OUT3_ is:
( )
R 13 =
-V OUT 3N
V REF 3 N
× R 14
A V = G C 3 _ × R IN || R 12 × A Q 4 _
SUP3N is the supply input for OUT3N’s transconduc-
tance amplifier. When OUT3N is used, SUP3N must be
A dominant pole (f POLE1 ) is created from the output
capacitance and load resistance:
connected to a voltage supply between 1.5V and 5.5V
that can source at least 25mA. Typically, V OUT1 can be
used as the supply input for SUP3N.
f POLE 1 =
1
2 π × C OUT 3 × R OUT 3
=
I OUT 3 _ MAX
2 π × C OUT 3 × V OUT 3 _
Stability Requirements
The MAX8513/MAX8514s’ DRV3P and DRV3N outputs
are designed to drive bipolar transistors (PNP types for
the MAX8513 with the DRV3P output, and NPN types
for the MAX8514 with the DRV3N output). These bipolar
transistors form linear regulators with positive outputs
(MAX8513 from 0.8V to 27V) and negative outputs
(MAX8514 from -18V to -1V). An internal transconduc-
tance amplifier is used to drive the external pass tran-
sistors. The transconductance amplifier, pass
Unity-gain crossover (f C_OUT3_ ) should occur at:
f C _ OUT 3 _ = A V × f POLE 1
A second pole is set by the input capacitance to the
base of Q4 (C Q4IN ), any external base-to-emitter
capacitance (C BE , see the Base-Drive Noise Reduction
section and Figure 7), the transistor’s input resistance
(R IN ), and the base-to-emitter pullup resistor (R12):
______________________________________________________________________________________
29
相关PDF资料 |
PDF描述 |
|---|---|
| EEC30DREI-S13 | CONN EDGECARD 60POS .100 EXTEND |
| V300C3V3H50B2 | CONVERTER MOD DC/DC 3.3V 50W |
| RSC06DRYI | CONN EDGECARD 12POS DIP .100 SLD |
| RMC06DRYI | CONN EDGECARD 12POS DIP .100 SLD |
| RBC13DRYI | CONN EDGECARD 26POS .100 EXTEND |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX8513EEI+ | 功能描述:DC/DC 开关控制器 Triple-Output Supply RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX8513EEI+T | 功能描述:DC/DC 开关控制器 Triple-Output Supply RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX8513EEI-T | 功能描述:DC/DC 开关控制器 RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX8513EVKIT | 功能描述:电源管理IC开发工具 RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| MAX8514AEI | 功能描述:DC/DC 开关控制器 RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
发布紧急采购，3分钟左右您将得到回复。