- 您现在的位置：买卖IC网 > PDF目录22320 > MAX8513EEI+ (Maxim Integrated)IC REG TRPL BUCK/LINEAR 28QSOP PDF资料下载
参数资料
| 型号： | MAX8513EEI+ |
| 厂商： | Maxim Integrated |
| 文件页数： | 27/35页 |
| 文件大小： | 0K |
| 描述： | IC REG TRPL BUCK/LINEAR 28QSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 50 |
| 拓扑： | 降压（降压）（1），线性（LDO）（2） |
| 功能： | 任何功能 |
| 输出数： | 3 |
| 频率 - 开关： | 250kHz ~ 1.5MHz |
| 电压/电流 - 输出 1： | 控制器 |
| 电压/电流 - 输出 2： | 控制器 |
| 电压/电流 - 输出 3： | 控制器 |
| 带 LED 驱动器： | 无 |
| 带监控器： | 无 |
| 带序列发生器： | 无 |
| 电源电压： | 4.5 V ~ 28 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 28-QSOP |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页当前第27页第28页第29页第30页第31页第32页第33页第34页第35页
Wide-Input, High-Frequency, Triple-Output Supplies
with Voltage Monitor and Power-On Reset
0 . 8 V G C 2 ( 1 + sCA × RA )
s ( CA + Cq ) ? 1 +
? ( 1 + sRA × Cq )
C 5
C 12 =
( 2 π × C 5 × R 3 × f P 3 ) - 1
12 nF
= = 53 . 3 pF
2 π × 12 nF × 20 k ? × 150 kHz - 1
Use 47pF.
Linear-Regulator Controllers
OUT2 Voltage Selection
The MAX8513/MAX8514 OUT2 positive linear regula-
tor’s output voltage is set by connecting a resistive-
divider from OUT2 to FB2 to GND. The resistors in the
divider are selected to set the minimum output current
(I OUT2_MIN ). For the Typical Applications Circuit (Figure
5 or Figure 6), the feedback resistors are set to R5 =
340 ? and R6 = 160 ? , where R5 is the resistor from
OUT2 to FB2 and R6 is the resistor from FB2 to GND.
These values set the minimum output current to
≈ 4.5mA, which works well with many MOSFETS.
In general,
the feedback resistors (R5 and R6) set the output-volt-
age reference point as well as the minimum load.
The loop gain for the positive LDO output using an
NMOS transistor is:
×
V OUT 2 ? sC OUT 2 ?
? g C ?
where C OUT2 is C6 in the Typical Applications Circuits .
G C2 is the transconductance of the internal amplifier
(0.21S typ), and a dominant pole at a low frequency is
created from this transconductance and the compen-
sation capacitor (C A in the Typical Applications Circuits
+ Q3’s gate capacitance (C q )). A second pole occurs
due to C OUT2 and the transconductance of Q3 (g C ).
This transconductance varies from a minimum g C(MIN)
occurring at minimum load to a maximum g C(MAX)
occurring at maximum load. To calculate the g C at any
load current, the typical forward transconductance can
be extracted from the MOSFET’s data sheet (gfs), as
I OUT 2 _ MIN =
I OUT 2 _ MAX
333
well as the current at which it is measured (IDfs). The
g C(MIN) and g C(MAX) can be calculated as:
Select R5 and R6 so:
g C ( MAX ) = gfs
I OUT 2(MAX )
IDfs
0.8V
R 6
= I OUT 2 _ MIN
g C ( MIN ) = gfs
I OUT 2(MIN)
IDfs
Poles occur at:
R 5 = R 6 × ? OUT 2 - 1 ?
? V ?
? 0 . 8 V ?
f PMAX =
g C ( MAX )
2 π × C OUT 2
OUT2 Stability
A transconductance amplifier drives the gate of the
and f PMIN =
g C ( MIN )
2 π × C OUT 2
g C ( MIN ) = OUT 2 MIN
NMOS transistor (Q3 in the Typical Applications
Circuits ), with current proportional to the error signal
multiplied by the amplifier ’s transconductance. The
error signal is the difference between V FB2 and the
internal 0.8V reference. V SUP2 , the supply voltage for
the transconductance amplifier, must be at least 1V
greater than the maximum required gate voltage
(V DRV2 ). The output pass transistor (Q3) buffers the
If only a minimum gfs is given, initially assume the max-
imum is twice the minimum.
When using a bipolar transistor, the g C(MAX) and
g C(MIN) occur at the following:
I
V T
DRV2 signal to produce the desired output voltage
(V OUT2 ). The output capacitor (C6 in the Typical
Applications Circuits ) helps bypass the output, while
g C ( MAX ) =
I OUT 2 MAX
V T
where V T is the thermal voltage, 26mV.
______________________________________________________________________________________
27
相关PDF资料 |
PDF描述 |
|---|---|
| EEC30DREI-S13 | CONN EDGECARD 60POS .100 EXTEND |
| V300C3V3H50B2 | CONVERTER MOD DC/DC 3.3V 50W |
| RSC06DRYI | CONN EDGECARD 12POS DIP .100 SLD |
| RMC06DRYI | CONN EDGECARD 12POS DIP .100 SLD |
| RBC13DRYI | CONN EDGECARD 26POS .100 EXTEND |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX8513EEI+ | 功能描述:DC/DC 开关控制器 Triple-Output Supply RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX8513EEI+T | 功能描述:DC/DC 开关控制器 Triple-Output Supply RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX8513EEI-T | 功能描述:DC/DC 开关控制器 RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX8513EVKIT | 功能描述:电源管理IC开发工具 RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| MAX8514AEI | 功能描述:DC/DC 开关控制器 RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
发布紧急采购，3分钟左右您将得到回复。