- 您现在的位置：买卖IC网 > PDF目录22318 > MAX8513EEI+T (Maxim Integrated)IC REG TRPL BUCK/LINEAR 28QSOP PDF资料下载
参数资料
| 型号： | MAX8513EEI+T |
| 厂商： | Maxim Integrated |
| 文件页数： | 21/35页 |
| 文件大小： | 0K |
| 描述： | IC REG TRPL BUCK/LINEAR 28QSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 拓扑： | 降压（降压）（1），线性（LDO）（2） |
| 功能： | 任何功能 |
| 输出数： | 3 |
| 频率 - 开关： | 250kHz ~ 1.5MHz |
| 电压/电流 - 输出 1： | 控制器 |
| 电压/电流 - 输出 2： | 控制器 |
| 电压/电流 - 输出 3： | 控制器 |
| 带 LED 驱动器： | 无 |
| 带监控器： | 无 |
| 带序列发生器： | 无 |
| 电源电压： | 4.5 V ~ 28 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 28-QSOP |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页当前第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页
Wide-Input, High-Frequency, Triple-Output Supplies
with Voltage Monitor and Power-On Reset
P Q 1 SW = V IN × I OUT 1 × f S ×
( Q GS + Q GD )
I GATE
1) Connect a scope probe to measure V LX to GND,
and observe the ringing frequency, f R .
2) Find the capacitor value (connected from LX to
GND) that reduces the ringing frequency by half.
(
R DH GATE )
L PAR =
( 2 π
× f R )
where I GATE is the average DH high driver output-cur-
rent capability determined by:
2 . 5 V
I GATE =
+ R
where R DH is the high-side MOSFET driver’s on-resis-
tance (1.5 ? typ) and R GATE is the internal gate resis-
tance of the MOSFET ( ≈ 2 ? ).
The circuit parasitic capacitance (C PAR ) at LX is then
equal to 1/3rd the value of the added capacitance above.
The circuit parasitic inductance (L PAR ) is calculated by:
1
2
× C PAR
The resistor for critical dampening (R SNUB ) is equal to
(2 π × f R × L PAR ). Adjust the resistor value up or down to
P Q 1 DR = Q GS × V GS × f S ×
R GATE
( R GATE + R DH
)
tailor the desired damping and the peak voltage excur-
sion. The capacitor (C SNUB ) should be at least 2 to 4
times the value of the C PAR to be effective. The power
loss of the snubber circuit is dissipated in the resistor
where V GS ≈ V VL = 5V.
The total power loss in Q1 is:
(P RSNUB ) and can be calculated as:
P Q 1 = P Q 1 CC + P Q 1 SW + P Q 1 DR
P RSNUB = C SNUB × ( V IN )
2
× f S
In addition to the losses above, allow approximately
20% more for additional losses due to MOSFET output
capacitances and Q2 body-diode reverse recovery
charge dissipated in Q1. This is not typically well-
defined in MOSFET data sheets. Refer to the MOSFET
data sheet for the thermal-resistance specification to
calculate the PC board area needed to maintain the
desired maximum operating junction temperature with
the above calculated power dissipations.
To reduce EMI caused by switching noise, add a 0.1μF
or larger ceramic capacitor from the high-side MOSFET
drain to the low-side MOSFET source or add resistors
in series with DH and DL to slow down the switching
transitions. However, adding series resistors with DH
and DL increases the power dissipation in the MOSFET
when it switches, so be sure this does not overheat the
MOSFET. The minimum load current must exceed the
high-side MOSFET’s maximum leakage current over
temperature if fault conditions are expected.
MOSFET Snubber Circuit
Fast switching transitions cause ringing because of res-
onating circuit parasitic inductance and capacitance at
the switching nodes. This high-frequency ringing
occurs at LX’s rising and falling transitions and can
interfere with circuit performance and generate EMI. To
dampen this ringing, a series-RC snubber circuit is
added across each switch. The following is the proce-
dure for selecting the value of the series-RC circuit:
where V IN is the input voltage and f S is the switching
frequency. Choose an R SNUB power rating that meets
the specific application’s derating rule for the power
dissipation calculated.
Current-Limit Setting
The MAX8513/MAX8514 can provide foldback current
limit or constant current limit. Unless constant current-
limit operation is required, such as when driving a con-
stant current load, foldback current limit should be
implemented. Foldback current limit reduces the power
dissipation of external components under overload or
short-circuit conditions.
Foldback Current Limit
For foldback current limit, the current-limit threshold is
set by an external resistive-divider from V OUT1 to ILIM to
GND (R17 and R18 of the Typical Applications Circuits ).
This makes the voltage at ILIM a function of the internal
5μA current source and V OUT1 . The current-limit com-
parator threshold is equal to V ILIM / 7.5. This threshold is
compared with V SENSE . V SENSE is either the voltage
across the current-sense resistor or, for lossless sens-
ing, the voltage across the inductor. When V SENSE
exceeds the current-limit threshold, the high-side
MOSFET turns off and the low-side MOSFET turns on.
This allows for a current foldback feature that reduces
the current-limit threshold during a short circuit. This
makes the current threshold limit, when V OUT = 0V, a
percentage of the current-limit threshold, when V OUT1 is
at its nominal regulated value.
______________________________________________________________________________________
21
相关PDF资料 |
PDF描述 |
|---|---|
| MAX5093BATE+T | IC REG DL BUCK/LINEAR 16TQFN |
| ABC35DRYI-S93 | CONN EDGECARD 70POS DIP .100 SLD |
| V300C12H75BF2 | CONVERTER MOD DC/DC 12V 75W |
| MAX786CAI+ | IC REG QD BCK/LINEAR SYNC 28SSOP |
| GCC05DREH-S734 | CONN EDGECARD 10POS .100 EYELET |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX8513EVKIT | 功能描述:电源管理IC开发工具 RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| MAX8514AEI | 功能描述:DC/DC 开关控制器 RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX8514AEI-T | 功能描述:DC/DC 开关控制器 RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX8514EEI | 功能描述:DC/DC 开关控制器 RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX8514EEI-T | 功能描述:DC/DC 开关控制器 RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
发布紧急采购，3分钟左右您将得到回复。