- 您现在的位置：买卖IC网 > PDF目录22318 > MAX8513EEI+T (Maxim Integrated)IC REG TRPL BUCK/LINEAR 28QSOP PDF资料下载
参数资料
| 型号： | MAX8513EEI+T |
| 厂商： | Maxim Integrated |
| 文件页数： | 22/35页 |
| 文件大小： | 0K |
| 描述： | IC REG TRPL BUCK/LINEAR 28QSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 拓扑： | 降压（降压）（1），线性（LDO）（2） |
| 功能： | 任何功能 |
| 输出数： | 3 |
| 频率 - 开关： | 250kHz ~ 1.5MHz |
| 电压/电流 - 输出 1： | 控制器 |
| 电压/电流 - 输出 2： | 控制器 |
| 电压/电流 - 输出 3： | 控制器 |
| 带 LED 驱动器： | 无 |
| 带监控器： | 无 |
| 带序列发生器： | 无 |
| 电源电压： | 4.5 V ~ 28 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 28-QSOP |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页当前第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页
Wide-Input, High-Frequency, Triple-Output Supplies
with Voltage Monitor and Power-On Reset
P FB = LIMIT @0 V
(
)
To set the current limit and the current-limit foldback
thresholds, first select the foldback current-limit ratio
(P FB ) . This ratio is the foldback current limit (I LIMIT@0V )
divided by the current limit when V OUT1 equals its nom-
inal regulated voltage (I LIMIT ).
I
I LIMIT
P FB is typically set to 0.5. To calculate the values of
R17 and R18 (in the Typical Applications Circuits ), use
the following equations:
C14 of the Typical Applications Circuits ). Pick the value
of the filter capacitor, C14, from 0.22μF to 1μF (ceramic
X7R). Then calculate the value of R19 as follows:
L 1 A
R 19 =
2 × R L _ DC × C 14
R L_DC is the nominal value of the inductor’s DC resis-
tance. Additionally, R20 (in the Typical Applications
Circuits ) is added in series with the CSN input to cancel
the drop due to input bias current into CSP that devel-
ops across R19. R20 should be set equal to R19.
( P FB × V OUT 1 )
4 . 7 μ A × ( 1 - P FB )
( 7 . 5 × R CS _ MAX LIMIT × ( 1 - P FB ) ) × R 17
V OUT 1 - ( 7 . 5 × R CS _ MAX LIMIT × ( 1 - P FB ) )
R 18 =
R 17 =
× I
× I
Compensation Design
The MAX8513/MAX8514 use a voltage-mode control
scheme that regulates the output voltage by comparing
the error-amplifier output (COMP) with a fixed internal
ramp to produce the required duty cycle. The output
lowpass LC filter creates a double pole at the resonant
frequency, which has a gain drop of -40dB/decade and
I OUT 1 _ MAX × ? ?
R CS_MAX is the maximum sensing resistance at the
high operating temperature. R CS can either be the
series resistance of the inductor or a discrete current-
sense resistor value. I LIMIT is the peak inductor current
at maximum load, which equals:
? 1 + LIR ?
? 2 ?
If R18 results in a negative resistance, then decrease
R CS . This can be done by choosing an inductor with a
lower DC resistance or a lower value discrete current-
sense resistor.
Constant Current Limit
a phase shift of approximately -180 ° /decade. The error
amplifier must compensate for this gain drop and
phase shift to achieve a stable high-bandwidth closed-
loop system.
The basic regulator loop consists of a power modulator,
an output feedback divider, and an error amplifier. The
power modulator has a DC gain set by V IN / V RAMP
(V RAMP = 1V P-P ), with a double pole and a single zero
set by the output inductance (L), the output capaci-
tance (C OUT ) (C4 in the Typical Applications Circuits ),
and its equivalent series resistance (R ESR ). V RAMP is
the peak of the saw-toothed waveform at the input of
the PWM comparator (see the Functional Diagrams in
Figures 1 and 2). Below are equations that define the
power modulator:
For constant current-limit operation, connect ILIM to VL
for a default current-limit threshold of 170mV (typ). The
sensing resistor value must then be chosen so that:
G MOD ( DC ) =
V IN
V RAMP
R CS_MAX × I LIMIT < 151mV
the minimum value of the default threshold.
f PMOD =
1
2 π L × C OUT
Alternately, the constant current-limit threshold can also
be set by using only R18, in which case R18 is calculat-
where L is L1A and C OUT is C4 in the Typical Applica-
tions Circuits .
R 18 = 7 . 5 × R CS _ MAX × LIMIT
ed as follows:
I
4 . 7 μ A
When using the DC resistance of the inductor as a cur-
rent-sense resistor, an RC filter is needed (R19 and
f ZESR =
1
2 π × C OUT × R ESR
22
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| MAX5093BATE+T | IC REG DL BUCK/LINEAR 16TQFN |
| ABC35DRYI-S93 | CONN EDGECARD 70POS DIP .100 SLD |
| V300C12H75BF2 | CONVERTER MOD DC/DC 12V 75W |
| MAX786CAI+ | IC REG QD BCK/LINEAR SYNC 28SSOP |
| GCC05DREH-S734 | CONN EDGECARD 10POS .100 EYELET |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX8513EVKIT | 功能描述:电源管理IC开发工具 RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| MAX8514AEI | 功能描述:DC/DC 开关控制器 RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX8514AEI-T | 功能描述:DC/DC 开关控制器 RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX8514EEI | 功能描述:DC/DC 开关控制器 RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX8514EEI-T | 功能描述:DC/DC 开关控制器 RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
发布紧急采购，3分钟左右您将得到回复。