- 您现在的位置：买卖IC网 > Datasheet目录341 > MAX8513EVKIT (Maxim Integrated Products)EVAL KIT FOR MAX8513 Datasheet资料下载
参数资料
| 型号： | MAX8513EVKIT |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 23/35页 |
| 文件大小： | 0K |
| 描述： | EVAL KIT FOR MAX8513 |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 1 |
| 主要目的： | DC/DC，LDO 步降 |
| 输出及类型： | 3，非隔离 |
| 输出电压： | 3.3V，2.5V，12V |
| 电流 - 输出： | 2A，1.5A，100mA |
| 输入电压： | 9 ~ 16 V |
| 稳压器拓扑结构： | 降压 |
| 频率 - 开关： | 1.4MHz |
| 板类型： | 完全填充 |
| 已供物品： | 板 |
| 已用 IC / 零件： | MAX8513 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页当前第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页
Wide-Input, High-Frequency, Triple-Output Supplies
with Voltage Monitor and Power-On Reset
When the output capacitance is comprised of parallel-
ing n number of identical capacitors whose values are
C EACH with ESR of R ESR_EACH , then:
C OUT = n × C EACH and
the -40dB/decade slope of the LC double pole, and the
resultant compensated loop crosses over at the
desired -20dB/decade slope. The error amplifier has a
dominant pole at very low frequency ( ≈ 0Hz), and two
separate zeros at:
R ESR =
R ESR _ EACH
n
f Z 1 =
1
2 π × R 3 × C 5
and f Z 2 =
1
2 π × ( R 1 + R 4 ) × C 11
Thus the resulting f ZESR is the same as that of each
capacitor.
and poles at:
2 π × R 3 × ? ?
The crossover frequency (f C ), which is the frequency
when the closed-loop gain is equal to unity, should be
the smaller of 1/5th the switching frequency or 100kHz
(see the Switching-Frequency Setting section):
f P 2 =
1
2 π × R 4 × C 11
and f P 3 =
1
? C 5 × C12 ?
? C 5 + C 12 ?
f C ≤ S or 100 kHz
f
5
The loop-gain equation at the crossover frequency is:
G EA ( fc ) G MOD ( fc ) = 1
The error-amplifier equivalent circuit and its gain vs.
frequency plot are shown below in Figure 3.
In this case, f Z2 and f P1 are selected to have the convert-
ers’ closed-loop crossover frequency, f C , occur when the
error-amplifier gain has a +20dB/decade slope between
f Z2 and f P2 . The error-amplifier gain at f C is:
where G EA(fc) is the error-amplifier gain at f C , and
G MOD( f c) is the power modular gain at f C .
The loop compensation is affected by the choice of out-
G EA ( fc ) =
1
G MOD ( fc )
put-filter capacitor used, due to the position of its ESR
The gain of the error amplifier between f Z1 and f Z2 is:
G EA ( fZ 1 - fZ 2 ) = G EA ( fc ) Z 2 =
zero frequency with respect to the desired closed-loop
crossover frequency. Ceramic capacitors are used for
higher switching frequencies (above 750kHz) because
of low capacitance and low ESR; therefore, the ESR
zero frequency is higher than the closed-loop crossover
frequency. While electrolytic capacitors (e.g., tantalum,
solid polymer, oscon, etc.) are needed for lower switch-
ing frequencies, because of high capacitance and ESR,
f
f C
C12
f Z 2
f C G MOD ( fc )
the ESR zero frequency is typically lower than the
closed-loop crossover frequency. Thus the compensa-
tion design procedure is separated into two cases:
V OUT1
C11
R4
R3
C5
Case 1: Ceramic Output Capacitor (operating at
high switching frequencies, f ZESR > f C )
R1
R2
REF
EA
COMP
G MOD ( fc ) = G MOD ( DC ) ? PMOD ?
The modulator gain at f C is:
? f ?
? f C ?
2
GAIN
(dB)
CLOSED-LOOP GAIN
EA GAIN
Since the crossover frequency is lower than the output
capacitors’ ESR zero frequency and higher than the LC
f Z1
f Z2
f P2
f P3
FREQUENCY
double-pole frequency, the error-amplifier gain must
have a +20dB/decade slope at f C . This +20dB/decade
slope of the error amplifier at crossover then adds to
f C
Figure 3. Case 1: Error-Amplifier Compensation Circuit (Closed-
Loop and Error-Amplifier Gain Plot)
______________________________________________________________________________________
23
相关PDF资料 |
PDF描述 |
|---|---|
| MAX8552EUB+ | IC DRIVER MOSFET HS 10-UMAX |
| MAX8595XETA+T | IC LED DRIVR WHITE BCKLGT 8-TDFN |
| MAX8607ETD+T | IC LED DRIVR PHOTO FLASH 14-TDFN |
| MAX8608YETD+T | IC LED DRVR WT/OLED BCKLT 14TDFN |
| MAX8631XETI+T | IC LED DRVR WHITE BCKLGT 28-TQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX8514AEI | 功能描述:DC/DC 开关控制器 RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX8514AEI-T | 功能描述:DC/DC 开关控制器 RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX8514EEI | 功能描述:DC/DC 开关控制器 RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX8514EEI-T | 功能描述:DC/DC 开关控制器 RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX8515AEXK | 制造商:Maxim Integrated Products 功能描述:WIDE-INPUT 0.6V SHUNT REGULATOR FOR - Rail/Tube 制造商:Rochester Electronics LLC 功能描述: |
发布紧急采购，3分钟左右您将得到回复。