- 您现在的位置：买卖IC网 > PDF目录16551 > MAX8588ETM+T (Maxim Integrated Products)IC PMIC HI EFF LOW IQ 48-TQFN PDF资料下载
参数资料
| 型号： | MAX8588ETM+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 19/31页 |
| 文件大小： | 0K |
| 描述： | IC PMIC HI EFF LOW IQ 48-TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 应用： | 处理器 |
| 电源电压： | 2.6 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 48-WFQFN 裸露焊盘 |
| 供应商设备封装： | 48-TQFN-EP（6x6） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页当前第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页
High-Efficiency, Low-I Q PMIC with
Dynamic Core for PDAs and Smartphones
V3 (VCC_CORE) Step-Down
DC-DC Converter
V3 is a 1MHz current-mode step-down converter. It sup-
plies loads up to 500mA.
The V3 output is set by the I 2 C serial interface to
between 0.7V and 1.475V in 25mV increments. The
default output voltage on power-up, and after a reset, is
1.3V. See the Serial Interface section for programming
details. See the Applications Information for instructions
on how to increase the V3 output voltage.
Forced PWM on REG3
Under moderate to heavy loading, the V3 always operates
in a low-noise PWM mode with constant frequency and
modulated pulse width. Switching harmonics generated by
fixed-frequency operation are consistent and easily filtered.
With light loads (<30mA) and PWM3 low, V3 operates
in an enhanced-efficiency idle mode during which the
converter switches only as needed to service the load.
With PWM3 high, V3 operates in low-noise forced-PWM
mode under all load conditions.
Linear Regulators (V4, V5, and V6)
V4 (VCC_PLL)
V4 is a linear regulator that provides a fixed 1.3V output
and supplies loads up to 35mA. The power input for the
V4 and V5 linear regulators is IN45, which is typically
connected to V2. To enable V4, drive ON4 high, or drive
ON4 low for shutdown. V4 is intended to connect to
VCC_PLL.
V5 (VCC_SRAM)
V5 is a linear regulator that provides a fixed 1.1V output
and supplies loads up to 35mA. The power input for the
V4 and V5 linear regulators is IN45, which is typically
connected to V2. To enable V5, drive ON5 high, or drive
ON5 low for shutdown. V5 is intended to connect to
VCC_SRAM.
V6 (VCC_USIM)
V6 is a linear regulator that supplies loads up to 35mA.
The V6 output voltage is programmed with the I 2 C seri-
al interface to 0V, 1.8V, 2.5V, or 3.0V. The power-up
default for V6 is 0V. See the Serial Interface section for
details on changing the voltage. The power input for the
V6 linear regulator is IN6, which is typically connected
to V1. To enable V6, drive ON6 high, or drive ON6 low
for shutdown. V6 is intended to connect to VCC_USIM.
V7 Always-On Output (VCC_BATT)
The V7 output is always active if V1 is enabled and in
regulation or if backup power is present. When ON1 is
high and V1 is in regulation, V7 is sourced from V1 by
an internal MOSFET switch. When ON1 is low or V1 is
out of regulation, V7 is sourced from BKBT by a second
on-chip MOSFET. V7 can supply loads up to 30mA. V7
is intended to connect to VCC_BATT on Intel CPUs.
Due to variations in system implementation, BKBT and
V7 can be utilized in different ways. See the Backup-
Battery Configurations section for information on how to
use BKBT and V7.
Quiescent Operating Current
in Various States
The MAX8588 is designed for optimum efficiency and
minimum operating current for all typical operating
modes, including sleep and deep sleep. These states
are outlined in Table 1.
Table 1. Quiescent Operating Current in Various States
OPERATING
POWER MODE
RUN
IDLE
SENSE
STANDBY
SLEEP
DEEP SLEEP
DESCRIPTION
All supplies on and running.
All supplies on and running, peripherals on.
All supplies on, minimal loading, peripherals monitored.
All supplies on, minimal loading, peripherals not monitored.
PWR_EN controlled voltages (V3, V4, V5) are off. V1 and V2 on.
All supplies off except V7. V7 biased from backup battery.
TYPICAL NO-LOAD
OPERATING CURRENT
225μA
60μA if V1 and V2 SLEEP LDOs on;
130μA if V1, V2 step-down DC-DCs enabled
32μA if IN > DBI threshold;
4μA if IN < DBI threshold
______________________________________________________________________________________
19
相关PDF资料 |
PDF描述 |
|---|---|
| SP1210R-681K | INDUCTOR PWR SHIELDED .680UH SMD |
| MAX1587AETL+T | IC POWER MANAGEMENT 40-TQFN |
| MAX1587CETL+T | IC POWER MANAGEMENT 40-TQFN |
| H3AWH-2036G | IDC CABLE - HSC20H/AE20G/HPL20H |
| SPD42R-563M | INDUCTOR PWR SHIELDED 56UH SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX858C/D | 功能描述:直流/直流开关转换器 DICE SALES DICE RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| MAX858CPA | 功能描述:直流/直流开关转换器 RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| MAX858CSA | 功能描述:直流/直流开关转换器 RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| MAX858CSA+ | 功能描述:直流/直流开关转换器 3.3/5/AdjV Step-Up DC/DC Converter RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| MAX858CSA+T | 功能描述:直流/直流开关转换器 3.3/5/AdjV Step-Up DC/DC Converter RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
发布紧急采购，3分钟左右您将得到回复。