- 您现在的位置：买卖IC网 > PDF目录1848 > MAX8632ETI+T (Maxim Integrated Products)IC PWR SUPPLY DDR 28-TQFN PDF资料下载
参数资料
| 型号： | MAX8632ETI+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 12/29页 |
| 文件大小： | 0K |
| 描述： | IC PWR SUPPLY DDR 28-TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 应用： | 控制器，DDR |
| 输入电压： | 2 V ~ 28 V |
| 输出数： | 1 |
| 输出电压： | 1.8V，2.5V，0.7 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-WFQFN 裸露焊盘 |
| 供应商设备封装： | 28-TQFN-EP（5x5） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页当前第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页
Integrated DDR Power-Supply Solution for
Desktops, Notebooks, and Graphic Cards
Detailed Description
The MAX8632 combines a synchronous-buck PWM con-
troller, an LDO linear regulator, and a 10mA reference out-
put buffer. The buck controller drives two external
n-channel MOSFETs to deliver load currents up to 15A
and generate voltages down to 0.7V from a +2V to +28V
input. The LDO linear regulator can sink and source up to
1.5A continuous and 3A peak current with relatively fast
response. These features make the MAX8632 ideally
suited for DDR memory applications.
The MAX8632 buck regulator is equipped with a fixed
switching frequency of up to 600kHz using Maxim’s
proprietary constant on-time Quick-PWM architecture.
This control scheme handles wide input/output voltage
ratios with ease, and provides 100ns “instant-on ”
response to load transients, while maintaining high effi-
ciency with relatively constant switching frequency.
The buck controller, LDO, and a reference output
buffer are provided with independent current limits.
Lossless foldback current limit in the buck regulator is
achieved by monitoring the drain-to-source voltage
drop of the low-side FET. The ILIM input is used to
adjust this current limit. Overvoltage protection, if
selected, is achieved by latching the low-side synchro-
nous FET on and the high-side FET off when the output
voltage is over 116% of its set output. It also features
an optional undervoltage protection by latching the
MOSFET drivers to the OFF state during an overcurrent
condition, when the output voltage is lower than 70% of
the regulated output. This helps minimize power dissi-
pation during a short-circuit condition.
The current limit in the LDO and buffered reference out-
put buffer is ±5A and ±32mA, respectively, and neither
the IC. The current from the AV DD and V DD power
supply must supply the current for the IC and the gate
drive for the MOSFETs. This maximum current can be
estimated as:
I BIAS = I VDD + I AVDD + f SW × ( Q G 1 + Q G 2 )
where I VDD + I AVDD are the quiescent supply currents
into V DD and AV DD , Q G1 and Q G2 are the total gate
charges of MOSFETs Q1 and Q2 (at V GS = 5V) in
Figure 8, and f SW is the switching frequency.
Free-Running Constant-On-Time PWM
The Quick-PWM control architecture is a pseudo-fixed-
frequency, constant on-time, current-mode regulator
with voltage feed-forward (Figure 1). This architecture
relies on the output filter capacitor’s ESR to act as a
current-sense resistor, so the output ripple voltage pro-
vides the PWM ramp signal. The control algorithm is
simple: the high-side switch on-time is determined
solely by a one-shot whose pulse width is inversely pro-
portional to input voltage and directly proportional to
the output voltage. Another one-shot sets a minimum
off-time of 300ns (typ). The on-time one-shot is trig-
gered if the error comparator is high, the low-side
switch current is below the valley current-limit thresh-
old, and the minimum off-time one-shot has timed out.
On-Time One-Shot (TON)
The heart of the PWM core is the one-shot that sets the
high-side switch on-time. This fast, low-jitter, adjustable
one-shot includes circuitry that varies the on-time in
response to input and output voltages. The high-side
switch on-time is inversely proportional to the input volt-
age (V IN ) and is proportional to the output voltage:
have the over- or undervoltage protection. When the
current limit in either output is reached, the output no
longer regulates the voltage, but regulates the current
to the value of the current limit.
t ON = K ×
( V OUT
+ I LOAD × R DS ( ON ) Q 2
V IN
)
+5V Bias Supply (V DD and AV DD )
The MAX8632 requires an external +5V bias supply in
addition to the input voltage (V IN ). Keeping the bias sup-
ply external to the IC improves the efficiency and elimi-
nates the cost associated with the +5V linear regulator
that would otherwise be needed to supply the PWM cir-
cuit and the gate drivers. If stand-alone capability is
needed, then the +5V supply can be generated with an
external linear regulator such as the MAX1615. V DD ,
AV DD , and IN can be connected together if the input
source is a fixed +4.5V to +5.5V supply.
V DD is the supply input for the buck regulator’s MOSFET
drivers, and AV DD supplies the power for the rest of
where K (the switching period) is set by the TON input
connection (Table 1) and R DS(ON)Q2 is the on-resis-
tance of the synchronous rectifier (Q2) in Figure 8. This
algorithm results in a nearly constant switching fre-
quency despite the lack of a fixed-frequency clock
generator. The benefits of a constant switching fre-
quency are twofold:
1) The frequency can be selected to avoid noise-sensi-
tive regions such as the 455kHz IF band.
2) The inductor ripple-current operating point remains
relatively constant, resulting in an easy design
methodology and predictable output voltage ripple.
12
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| MAX8636ETA+T | IC REG LDO ADJ .3A 8TDFN |
| MAX8640YEXT08+T | IC REG BUCK SYNC 0.8V .5A SC70-6 |
| MAX8643AETG/V+T | IC REG BUCK SYNC ADJ 3A 24TQFN |
| MAX8643ETG+T | IC REG BUCK SYNC ADJ 3A 24TQFN |
| MAX8646ETG+T | IC REG BUCK SYNC ADJ 6A 24TQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX8632EVKIT | 功能描述:电源管理IC开发工具 RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| MAX8633ELA+ | 制造商:Maxim Integrated Products 功能描述: |
| MAX8633ELA+T | 功能描述:低压差稳压器 - LDO Dual 300mA Pin-Prog LDO RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| MAX8633ETA+ | 制造商:Maxim Integrated Products 功能描述:LDO REG 1.5V TO 3V 0.3A 8TDFN EP - Rail/Tube |
| MAX8633ETA+T | 功能描述:低压差稳压器 - LDO Dual 300mA Pin-Prog LDO RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
发布紧急采购，3分钟左右您将得到回复。