- 您现在的位置：买卖IC网 > PDF目录17278 > MAX8686EVKIT+ (Maxim Integrated Products)BOARD EVAL FOR MAX8686 PDF资料下载
参数资料
| 型号： | MAX8686EVKIT+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 11/23页 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL FOR MAX8686 |
| 标准包装： | 1 |
| 主要目的： | DC/DC，步降 |
| 输出及类型： | 1，非隔离 |
| 输出电压： | 0.7 V ~ 5.5 V |
| 电流 - 输出： | 25A |
| 输入电压： | 4.5 V ~ 20 V |
| 稳压器拓扑结构： | 降压 |
| 频率 - 开关： | 300kHz ~ 1MHz |
| 板类型： | 完全填充 |
| 已供物品： | 板 |
| 已用 IC / 零件： | MAX8686 |
Single/Multiphase, Step-Down,
DC-DC Converter Delivers Up to 25A Per Phase
Detailed Description
DC-DC Converter Control Architecture
The MAX8686 step-down regulator uses a PWM, cur-
rent-mode control scheme. An internal transconduc-
tance amplifier establishes an integrated error voltage.
The heart of the PWM controller is a PWM comparator
that compares the integrated voltage-feedback signal
against the amplified current-sense signal plus an
adjustable slope-compensation ramp, which is
summed with the current signal to ensure stability. At
each rising edge of the internal clock, the internal high-
side MOSFET turns on until the PWM comparator trips
or the maximum duty cycle is reached. During this on-
time, current ramps up through the inductor, storing
energy in the inductor while sourcing current to the
output. The current-mode feedback system regulates the
peak inductor current as a function of the output-voltage
error signal. The circuit acts as a switch-mode transcon-
ductance amplifier and pushes an output LC filter pole
normally found in a voltage-mode PWM to a higher fre-
quency. See the Functional Diagram.
During the second half of the cycle, the internal high-side
MOSFET turns off and the internal low-side MOSFET
turns on. The inductor releases the stored energy as the
current ramps down, providing current to the load. The
output capacitor stores charge when the inductor cur-
rent exceeds the required load current and discharges
when the inductor current is lower, smoothing the volt-
age across the load. Under soft-overload conditions,
when the peak inductor current exceeds the selected
current limit (see the Current-Limit Circuit section), the
high-side MOSFET is turned off immediately and the
low-side MOSFET is turned on and remains on to let the
inductor current ramp down until the next clock cycle.
Under severe-overload or short-circuit conditions, the
foldback/hiccup current limit is enabled to reduce
power dissipation.
The MAX8686 operates in a forced-PWM mode. The
converter maintains a constant switching frequency,
regardless of load, to allow for easier filtering of the
switching noise.
Internal Linear Regulator (VL)
The MAX8686 contains an internal LDO regulator that
provides a 5.4V supply for the MOSFET gate drivers.
Connect at least a 1μF ceramic capacitor from VL to
RTN. VL also provides power to the internal analog cir-
cuit through AVL. Connect an RC lowpass filter (R =
10 Ω , C = 0.22μF) from VL to AVL.
Undervoltage Lockout
When AVL drops below 4.03V, the MAX8686 assumes
that the supply voltage is too low to make valid deci-
sions, so the undervoltage-lockout (UVLO) circuitry
inhibits switching and turns off both power MOSFETs.
When AVL rises above 4.35V, the regulator enters the
startup sequence and then resumes normal operation.
When operating in a multiphase configuration, the AVL
of all the devices must exceed the UVLO threshold
before any switching begins. This is achieved through
the shared ILIM pin, which is pulled low in UVLO.
Startup, Soft-Start, and Prebias Operation
The internal soft-start circuitry gradually ramps up the
reference voltage in order to control the rate of rise of
the output voltage and reduce input surge currents dur-
ing startup. The soft-start time is determined by the
value of the capacitor from SS to GND and is approxi-
mately equal to 50ms per microfarad of the capacitor.
In addition, the MAX8686 features monotonic output-
voltage rise (prebias); therefore, both power MOSFETs
are kept off if the voltage between the remote sense
input (RS+, RS-) is higher than the voltage at REFIN.
This allows the MAX8686 to start up into a prebiased
output without pulling the output voltage down.
Before the MAX8686 can begin the soft-start and
power-up sequence, the following conditions must be
met: AVL exceeds the 4.35V UVLO threshold, EN is at
logic-high, and the thermal limit is not exceeded.
Reference Output
(PHASE/REFO)/Reference Input (REFIN)
The reference voltage REFO can be used to set the out-
put voltage by scaling this voltage down with a resistive
divider and using it as the input voltage to the reference
input, REFIN. The 3.3V reference voltage is 1% accurate
over temperature and can source up to 20μA.
The reference input REFIN allows the reference value of
the device to be set by an external reference. In most
applications, the 3.3V voltage with 1% accuracy from
the PHASE/REFO pin should be used as the reference.
This can be achieved by dividing the 3.3V voltage to
the desired output voltage.
______________________________________________________________________________________
11
相关PDF资料 |
PDF描述 |
|---|---|
| EBC07DRTF | CONN EDGECARD 14POS DIP .100 SLD |
| EEV-FC1H3R3R | CAP ALUM 3.3UF 50V 20% SMD |
| EEC12DRAI | CONN EDGECARD 24POS R/A .100 SLD |
| ECC17DCMS | CONN EDGECARD 34POS .100 WW |
| R1D-1524 | CONV DC/DC 1W 15VIN +/-24VOUT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX8686EVKIT# | 功能描述:电源管理IC开发工具 MAX8686 Eval Kit RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| MAX8686EVKIT+ | 功能描述:电源管理IC开发工具 MAX8686 Eval Kit RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| MAX8687ETL+ | 制造商:Maxim Integrated Products 功能描述:SINGLE /MULTIPHASE, DC/DC CONVERTER - Rail/Tube |
| MAX8688AHETG+ | 功能描述:电流和电力监控器、调节器 Digital Power-Supply Controller/Monitor RoHS:否 制造商:STMicroelectronics 产品:Current Regulators 电源电压-最大:48 V 电源电压-最小:5.5 V 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:HPSO-8 封装:Reel |
| MAX8688AHETG+T | 功能描述:电流和电力监控器、调节器 Digital Power-Supply Controller/Monitor RoHS:否 制造商:STMicroelectronics 产品:Current Regulators 电源电压-最大:48 V 电源电压-最小:5.5 V 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:HPSO-8 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。