- 您现在的位置：买卖IC网 > PDF目录1848 > MAX8707ETL+ (Maxim Integrated Products)IC CNTRLR MULTIPHASE 40TQFN PDF资料下载
参数资料
| 型号： | MAX8707ETL+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 26/37页 |
| 文件大小： | 0K |
| 描述： | IC CNTRLR MULTIPHASE 40TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 50 |
| 应用： | 控制器，AMD Hammer |
| 输入电压： | 4.5 V ~ 5.5 V |
| 输出数： | 4 |
| 输出电压： | 0.8 V ~ 1.55 V |
| 工作温度： | 0°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 40-WFQFN 裸露焊盘 |
| 供应商设备封装： | 40-TQFN-EP（6x6） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页当前第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页
Multiphase, Fixed-Frequency Controller for
AMD Hammer CPU Core Power Supplies
Table 5. SKIP Settings
SKIP
(INPUT)
SUS
(INPUT)
MODE
DRSKP
(OUTPUT)
OPERATION
The controller operates with a constant switching
Low
(GND)
Low
(GND)
Multiphase
Forced-PWM
High
(V DD )
frequency, providing low-noise forced-PWM operation. The
controller disables the zero-crossing comparators, forcing
the low-side gate-drive waveform to constantly be the
complement of the high-side gate-drive waveform.
The controller automatically switches to pulse-skipping
operation 20μs after the target voltage reaches the SUSV
High
(3.3V or V CC )
1-Phase Pulse
Skipping
Low
(PGND)
voltage. Pulse-skipping operation forces the controller into
PFM operation under light loads. Phase 1 remains active
while the other three phases are disabled — PWM2, PWM3,
and PWM4 pulled low.
Pulse-skipping operation forces the controller into PFM
High
(>1.2V)
Don ’ t Care
1-Phase Pulse
Skipping
Low
(PGND)
operation under light loads. Phase 1 remains active while
the other three phases are disabled — PWM2, PWM3, and
PWM4 pulled low.
sense voltage exceeds the Idle Mode ? current-sense
threshold (V IDLE = 0.1 x V PKLIMIT ). Under heavy-load
conditions, the continuous inductor current remains
above the Idle-Mode current-sense threshold, so the
on-time depends only on the feedback-voltage thresh-
old. Under light-load conditions, the controller remains
above the feedback-voltage threshold, so the on-time
duration depends solely on the Idle-Mode current-
sense threshold, which is approximately 10% of the full-
load current-limit threshold set by ILIM(PK).
When the controller enters suspend mode while SKIP is
pulled high, the multiphase controller immediately dis-
ables three phases, and only the main phase (PWM1)
remains active. When pulse skipping, the controller
blanks the upper VROK threshold and the OVP threshold
tracks the selected VID DAC code. The MAX8707 auto-
matically uses forced-PWM operation during soft-start
and soft-shutdown, regardless of the SKIP configuration.
Idle-Mode Current Sense Threshold
The Idle-Mode current-sense threshold forces a lightly
loaded regulator to source a minimum amount of ener-
gy with each on-time since the controller cannot termi-
troller does not initiate another on-time. This forces the
controller to actually regulate the valley of the output
voltage ripple under light-load conditions.
Automatic Pulse-Skipping Crossover
In skip mode, the MAX8707 disables three phases and
forces DRSKP low to instruct the skip-mode drivers to
activate their zero-crossing comparators. Therefore, an
inherent automatic switchover to PFM takes place at light
loads ( Figure 6), resulting in a highly efficient operating
mode. This switchover is affected by a comparator that
truncates the low-side switch on-time at the inductor cur-
rent ’ s zero crossing. The driver ’ s zero-crossing compara-
tor senses the inductor current across the low-side
MOSFET (refer to the skip-mode driver data sheet).
Once V LX - V PGND drops below the zero-crossing
threshold, the driver forces DL low. This mechanism
causes the threshold between pulse-skipping PFM and
nonskipping PWM operation to coincide with the bound-
ary between continuous and discontinuous inductor-cur-
rent operation (also known as the critical conduction
point). The load-current level at which the PFM/PWM
crossover occurs, I LOAD(SKIP) , is given by:
nate the on-time until the current-sense voltage
exceeds the Idle-Mode current-sense threshold (V IDLE
= 0.1 x V PKLIMIT ). Since the zero-crossing comparator
prevents the switching regulator from sinking current,
I LOAD ( SKIP ) =
V OUT ( V IN ? V OUT )
2 V IN f SW L
the controller must skip pulses to avoid overcharging
the output. When the clock edge occurs, if the output
voltage still exceeds the feedback threshold, the con-
Idle Mode is a trademark of Maxim Integrated Products, Inc.
The switching waveforms may appear noisy and asyn-
chronous when light loading causes pulse-skipping
operation, but this is a normal operating condition that
26
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| MAX8709BETI+T | IC CNTRLR CCFL HI EFF 28-TQFN |
| MAX8719ETA+T | IC REG LINEAR LP HV 8-TDFN |
| MAX871EUK+TG002 | IC VOLTAGE INV SWCAP SOT23-5 |
| MAX8720ETX+ | IC CNTRL VID STP DWN 36-TQFN |
| MAX8722CEEG+ | IC CCFL BACKLIGHT CTRL 24-QSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX8707ETL+ | 功能描述:DC/DC 开关控制器 Multiphase Fixed Frequency Controller RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX8707ETL+T | 功能描述:DC/DC 开关控制器 Multiphase Fixed Frequency Controller RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX8707ETL-T | 功能描述:DC/DC 开关控制器 RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX8708ETJ | 制造商:Maxim Integrated Products 功能描述:AMD CPU CORE SUPPLY - Rail/Tube |
| MAX8708ETJ-T | 制造商:Maxim Integrated Products 功能描述:AMD CPU CORE SUPPLY - Tape and Reel |
发布紧急采购，3分钟左右您将得到回复。