- 您现在的位置：买卖IC网 > PDF目录1849 > MAX8795AETJ+C7P (Maxim Integrated Products)IC TFT-LCD DC/DC CONV 32-TQFN PDF资料下载
参数资料
| 型号： | MAX8795AETJ+C7P |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 24/31页 |
| 文件大小： | 0K |
| 描述： | IC TFT-LCD DC/DC CONV 32-TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 60 |
| 应用： | 转换器，TFT，LCD |
| 输入电压： | 2.5 V ~ 6 V |
| 输出数： | 8 |
| 输出电压： | 2.5 V ~ 18 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-WFQFN 裸露焊盘 |
| 供应商设备封装： | 32-TQFN-EP（5x5） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页当前第24页第25页第26页第27页第28页第29页第30页第31页
TFT-LCD DC-DC Converter with
Operational Amplifiers
and gate-off linear-regulator controllers are 0.1mA.
Therefore, the base-to-emitter resistor for both linear
regulators should be chosen to set 0.1mA bias current:
4) Next, calculate the pole set by the linear regulator’s
feedback resistance and the capacitance between
FB_ and AGND (including stray capacitance):
R BE =
= ≈ 6 . 8 k ?
V BE 0 . 7 V
0 . 1 mA 0 . 1 mA
The output capacitor and the load resistance create the
f POLE _ FB =
1
2 π × C FB × ( R UPPER || R LOWER )
f POLE _ LR =
f POLE _ ESR =
dominant pole in the system. However, the internal
amplifier delay, pass transistor’s input capacitance,
and the stray capacitance at the feedback node create
additional poles in the system, and the output capaci-
tor’s ESR generates a zero. For proper operation, use
the following equations to verify the linear regulator is
properly compensated:
1) First, determine the dominant pole set by the linear
regulator’s output capacitor and the load resistor:
I LOAD ( MAX )_ LR
2 π × C OUT _ LR × V OUT _ LR
The unity-gain crossover of the linear regulator is:
f CROSSOVER = A V_LR f POLE_LR
2) The pole created by the internal amplifier delay is
approximately 1MHz:
f POLE_AMP = 1MHz
3) Next, calculate the pole set by the transistor’s input
capacitance, the transistor’s input resistance, and
the base-to-emitter pullup resistor:
where CFB is the capacitance between FB_ and
AGND, R UPPER is the upper resistor of the linear regu-
lator’s feedback divider, and R LOWER is the lower resis-
tor of the divider.
5) Next, calculate the zero caused by the output
capacitor’s ESR:
1
2 π × C OUT _ LR × R ESR
where RESR is the equivalent series resistance of
COUT_LR.
To ensure stability, choose C OUT_LR large enough so
the crossover occurs well before the poles and zero
calculated in steps 2 to 5. The poles in steps 3 and 4
generally occur at several megahertz, and using
ceramic capacitors ensures the ESR zero occurs at
several megahertz as well. Placing the crossover below
500kHz is sufficient to avoid the amplifier-delay pole
and generally works well, unless unusual component
choices or extra capacitances move one of the other
f POLE _ IN =
1
2 π × C IN × ( R BE || R IN )
poles or the zero below 1MHz.
Applications Information
C IN =
, R IN =
where :
g m h FE
2 π f T g m
g m is the transconductance of the pass transistor, and f T
is the transition frequency. Both parameters can be found
in the transistor’s data sheet. Because RBE is much
greater than RIN, the above equation can be simplified:
Power Dissipation
An IC’s maximum power dissipation depends on the
thermal resistance from the die to the ambient environ-
ment and the ambient temperature. The thermal resis-
tance depends on the IC package, PCB copper area,
other thermal mass, and airflow.
The MAX8795A, with its exposed backside paddle sol-
dered to 1in 2 of PCB copper and a large internal ground
f POLE _ IN =
1
2 π × C IN × R IN
plane layer, can dissipate approximately 2.76W into
+70 ° C still air. More PCB copper, cooler ambient air,
and more airflow increase the possible dissipation, while
f POLE _ IN = T
Substituting for CIN and RIN yields:
f
h FE
less copper or warmer air decreases the IC’s dissipation
capability. The major components of power dissipation
are the power dissipated in the step-up regulator and
the power dissipated by the operational amplifiers.
24
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| MAX8798ETX+T | IC INTERNAL-SW BOOST REG 36-TQFN |
| MAX8804VETA+T | IC USB/AC ADP CHARGER 8TDFN-EP |
| MAX8804YETA+T | IC USB/AC ADP CHARGER 8-TDFN |
| MAX8805WEWECE+T | IC PWM STEP-DN CONV 650MA 16-WLP |
| MAX8808XETA+T | IC BATT CHRGR 1-CELL LI+ 8TDFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX8795AEVKIT+ | 功能描述:电源管理IC开发工具 MAX8795A Eval Kit RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| MAX8795AGCJ/V+ | 功能描述:LCD 驱动器 TFT-LCD DC/DC Converter RoHS:否 制造商:Maxim Integrated 数位数量:4.5 片段数量:30 最大时钟频率:19 KHz 工作电源电压:3 V to 3.6 V 最大工作温度:+ 85 C 最小工作温度:- 20 C 封装 / 箱体:PDIP-40 封装:Tube |
| MAX8795AGCJ/V+T | 功能描述:LCD 驱动器 TFT-LCD DC/DC Converter RoHS:否 制造商:Maxim Integrated 数位数量:4.5 片段数量:30 最大时钟频率:19 KHz 工作电源电压:3 V to 3.6 V 最大工作温度:+ 85 C 最小工作温度:- 20 C 封装 / 箱体:PDIP-40 封装:Tube |
| MAX8795AGCJ+ | 功能描述:LCD 驱动器 TFT-LCD DC/DC Converter RoHS:否 制造商:Maxim Integrated 数位数量:4.5 片段数量:30 最大时钟频率:19 KHz 工作电源电压:3 V to 3.6 V 最大工作温度:+ 85 C 最小工作温度:- 20 C 封装 / 箱体:PDIP-40 封装:Tube |
| MAX8795AGCJ+T | 功能描述:LCD 驱动器 TFT-LCD DC/DC Converter RoHS:否 制造商:Maxim Integrated 数位数量:4.5 片段数量:30 最大时钟频率:19 KHz 工作电源电压:3 V to 3.6 V 最大工作温度:+ 85 C 最小工作温度:- 20 C 封装 / 箱体:PDIP-40 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。