- 您现在的位置：买卖IC网 > Datasheet目录341 > MAX8831EWE+T (Maxim Integrated)IC LED DRIVR WHITE BCKLGT 16-WLP Datasheet资料下载
参数资料
| 型号： | MAX8831EWE+T |
| 厂商： | Maxim Integrated |
| 文件页数： | 19/28页 |
| 文件大小： | 0K |
| 描述： | IC LED DRIVR WHITE BCKLGT 16-WLP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 1 |
| 拓扑： | 线性（LDO），PWM，升压（升压） |
| 输出数： | 5 |
| 内部驱动器： | 是 |
| 类型 - 主要： | 背光 |
| 类型 - 次要： | 白色 LED |
| 频率： | 1.8MHz ~ 2.2MHz |
| 电源电压： | 1.6 V ~ 5.5 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-UFBGA，WLCSP |
| 供应商设备封装： | 16-WLP（2x2） |
| 包装： | 标准包装 |
| 工作温度： | -40°C ~ 85°C |
| 其它名称： | MAX8831EWE+TDKR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页当前第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
High-Efficiency, White LED Step-Up Converter
with I 2 C Interface in 2mm x 2mm WLP
The typical value for the input capacitor is 1μF, and the
typical value for the output capacitor is 1μF. Higher
value capacitors can reduce input and output ripple,
but at the expense of size and higher cost.
not returning to minimum current before turning off dur-
ing the blink OFF time. The blink ON and blink OFF
timers (t ON_BLINK and t OFF_BLINK ) are programmed
according to the following equations as guidance:
Diode Selection
The high switching frequency of the MAX8831
demands a high-speed rectification diode for optimum
t ON _ BLINK ≥
t LED _ RU
32
( LED _ CODE + 1 )
efficiency. A Schottky diode is recommended due to its
fast recovery time and low forward voltage drop.
Ensure that the diode’s average and peak current rat-
t OFF _ BLINK ≥
t LED _ RD
32
( LED _ CODE + 1 )
ing exceeds the average output current and peak
inductor current. In addition, the diode’s reverse break-
down voltage must exceed V OUT .
Compensation Network Selection
The step-up converter is compensated for stability
through an external compensation network from COMP
to GND. The compensation capacitor is typically
0.22μF for most applications. Note that higher C COMP
values increase soft-start duration, as well as the time
delay between enabling the step-up converter to initiat-
ing soft-start.
Combining BLINK Timer
and RAMP Functions
When using the ramp functionality of LED3, LED4, and
LED5 in combination with the blink timer, it is recom-
mended to keep the ramp-up timer shorter than the
blink ON timer and the ramp-down timer shorter than
the blink OFF timer. See Figure 14. Failing to comply
with this restriction results in LED_ current not reaching
maximum value during blink ON time, and LED_ current
Where t LED_RU is the LED_ ramp-up time, t LED_RD is
the LED_ ramp-down time, and LED_CODE is the deci-
mal equivalent of the ILED_CNTL register value of
Table 2.
Using the LED3, LED4, and LED5
BOOST_CNTRL Bit
The default setting of the BOOST_CNTL bits (low)
include the LED3, LED4, and LED5 current regulators
in the step-up converter minimum voltage select feed-
back circuit. This is intended for multi-LED strings pow-
ered from the step-up converter. For single LED
indicator lights, set the respective BOOST_CNTL bit
high, connect the LED anode to the battery or other
voltage source, and connect the LED cathode to the
respective LED_ input. Ensure the voltage source is
high enough to satisfy VF of the LED plus 150mV (cur-
rent regulator dropout voltage). If BOOST_CNTL bits
are set to high for LED3, LED4, and LED5 and LED1
and LED2 are not enabled, the step-up converter does
not turn on when LED3, LED4, or LED5 is enabled.
BLINK TIMERS
I LED = ILED_CNTL
REGISTER SETTING
I LED_ = OFF
t ON_BLINK
t OFF_BLINK
t ON_BLINK
t=
t LED_RU
32
t=
t LED_RU
32
Figure 14. Combined Timing Characteristics of RAMP and BLINK Timers
______________________________________________________________________________________
19
相关PDF资料 |
PDF描述 |
|---|---|
| MAX8834ZEWP+T | IC LED DRIVR BCKLGT FLASH 20-WLP |
| MAX8855EVKIT+ | KIT EVAL FOR MAX8855 |
| MAX8879ETG+T | IC LED DRVR WT/RGB BCKLGT 24TQFN |
| MAX8901BETA+TCH8 | IC LED DRIVER WHITE BCKLGT 8TDFN |
| MAX8930EWJ+T | IC LED DRVR WT/RGB BCKLGT 49WLP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX8833ETJ+ | 功能描述:直流/直流开关调节器 Dual 3A 2MHz Step-Down Regulator RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| MAX8833ETJ+T | 功能描述:直流/直流开关调节器 Dual 3A 2MHz Step-Down Regulator RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| MAX8834YEVKIT+ | 功能描述:LED 照明开发工具 Adaptive Step-Up Converters with 1.5A Flash Driver RoHS:否 制造商:Fairchild Semiconductor 产品:Evaluation Kits 用于:FL7732 核心: 电源电压:120V 系列: 封装: |
| MAX8834YEWP+T | 功能描述:LED照明驱动器 Adaptive Step-Up Converter RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| MAX8834ZEWP+T | 功能描述:LED照明驱动器 Adaptive Step-Up Converter RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
发布紧急采购，3分钟左右您将得到回复。