- 您现在的位置：买卖IC网 > PDF目录14487 > MAX8833ETJ+ (Maxim Integrated Products)IC REG BUCK ADJ 3A DL 32TQFN PDF资料下载
参数资料
| 型号： | MAX8833ETJ+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 16/20页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK ADJ 3A DL 32TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 60 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 2 |
| 输出电压： | 0.6 V ~ 3.24 V |
| 输入电压： | 2.35 V ~ 3.6 V |
| PWM 型： | 电压模式 |
| 频率 - 开关： | 1MHz ~ 2MHz |
| 电流 - 输出： | 3A |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-WFQFN 裸露焊盘 |
| 包装： | 管件 |
| 供应商设备封装： | 32-TQFN-EP（5x5） |
Dual, 3A, 2MHz Step-Down Regulator
Set the second compensation pole at 1/2 the switching
frequency. Calculate C10 as follows:
?
A multilayer PCB is recommended. Use inner-layer
ground (and power) planes to minimize noise coupling.
C 10 =
1
π × R 7 × f S
?
Place the input ceramic decoupling capacitor
directly across and as close as possible to IN_ and
PGND_. This is to help contain the high switching
currents within a small loop.
C O × ≥ P ? P
The recommended range for R4 is 2kΩ to 10kΩ. Note
that the loop compensation remains unchanged if only
R6’s resistance is altered to set different outputs.
Safe-Starting into a Prebiased Output
The MAX8833 is capable of safe-starting up into a pre-
biased output without discharging the output capacitor.
This type of operation is also termed monotonic startup.
However, in order to avoid output voltage glitches dur-
ing safe-start it should be ensured that the inductor cur-
rent is in continuous conduction mode during the end
of the soft-start period, this is done by satisfying the fol-
lowing equation:
V O I
t SS 2
where C O is the output capacitor, V O is the output volt-
age, t SS is the soft-start time set by the soft-start capac-
itor C SS , and I P-P is the peak inductor ripple current (as
defined in the Output-Capacitor Selection section).
Depending on the application, one of these parameters
may drive the selection of the others. See Starting into
Prebiased Output waveforms in the Typical Operating
Characteristics section for an example selection of the
above parameters.
Applications Informations
PCB Layout Guidelines
Careful PCB layout is critical to achieve low switching
losses and clean, stable operation. The switching
power stage requires particular attention. It is highly
recommended to duplicate the MAX8833 layout for
optimum performance. If deviation is necessary, follow
these guidelines for a good PCB layout:
?
?
?
?
?
?
?
?
Connect IN_ and PGND_ separately to large copper
areas to help cool the IC and further improve effi-
ciency and long-term reliability.
Connect input, output, and VDL capacitors to the
power ground plane (PGND_).
Keep the path of switching currents short and mini-
mize the loop area formed by LX_, the output
capacitor(s), and the input capacitor(s).
Place the IC decoupling capacitors as close as
possible to the IC pins, connecting all other ground-
terminated capacitors, resistors, and passive com-
ponents to the reference or analog ground plane
(GND).
Separate the power and analog ground planes,
using a single-point common connection point (typi-
cally, at the C IN_ cathode.
Connect the exposed pad to the analog ground
plane, allowing sufficient copper area to help cool
the device. If the exposed pad is used as a com-
mon PGND_-to-GND connection point, avoid run-
ning high current through the exposed pad by
using separate vias to connect the PGND_ pins to
the power ground plane rather than connecting
them to the exposed pad on the top layer.
Use caution when routing feedback and compensa-
tion node traces; avoid routing near high dV/dt
nodes (LX_) and high-current paths. Place the feed-
back and compensation components as close as
possible to the IC pins.
Reference the MAX8833 Evaluation Kit for an exam-
ple layout.
16
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| MAX1708EEE+ | IC REG BST 3.3V/5V/ADJ 5A 16QSOP |
| MAX660ESA+ | IC REG SWITCHD CAP DBL INV 8SOIC |
| MAX1774EEI+ | IC REG BUCK SYNC ADJ DL 28QSOP |
| MAX5033BASA+ | IC REG BUCK 5V 0.5A 8SOIC |
| GCC43DREI | CONN EDGECARD 86POS .100 EYELET |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX8833ETJ+ | 功能描述:直流/直流开关调节器 Dual 3A 2MHz Step-Down Regulator RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| MAX8833ETJ+T | 功能描述:直流/直流开关调节器 Dual 3A 2MHz Step-Down Regulator RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| MAX8834YEVKIT+ | 功能描述:LED 照明开发工具 Adaptive Step-Up Converters with 1.5A Flash Driver RoHS:否 制造商:Fairchild Semiconductor 产品:Evaluation Kits 用于:FL7732 核心: 电源电压:120V 系列: 封装: |
| MAX8834YEWP+T | 功能描述:LED照明驱动器 Adaptive Step-Up Converter RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| MAX8834ZEWP+T | 功能描述:LED照明驱动器 Adaptive Step-Up Converter RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
发布紧急采购，3分钟左右您将得到回复。