- 您现在的位置：买卖IC网 > PDF目录1850 > MAX8922LETB+T (Maxim Integrated Products)IC BATTERY CHARGER SGL 10TDFN PDF资料下载
参数资料
| 型号： | MAX8922LETB+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 10/15页 |
| 文件大小： | 0K |
| 描述： | IC BATTERY CHARGER SGL 10TDFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 功能： | 充电管理 |
| 电池化学： | 锂离子（Li-Ion） |
| 电源电压： | 0 V ~ 28 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-WFDFN 裸露焊盘 |
| 供应商设备封装： | 10-TDFN EP（3x2） |
| 包装： | 带卷 (TR) |
30V Li+ Linear Battery Charger
with GSM Test Mode in 3mm x 2mm TDFN
AC
ADAPTER
C1
1 μ F
IN
BAT
C2
2.2 μ F
4.2V
Li+
SYSTEM
R1
1.87k ?
MIN
LDO
C3
1 μ F
VI/O
VBUS
MAX8922L
SETI
R2
3k ?
Figure 4. AC Adapter Charger Application
EP
GND TEST
POK
CHG
EN/SET
GPIO
GPIO
GPIO
Thermal Considerations
The MAX8922L is in a thermally enhanced TDFN pack-
age with an exposed pad. Connect the exposed pad of
the package to a large copper ground plane to provide a
thermal contact between the device and the circuit board.
The exposed pad transfers heat away from the device,
allowing the IC to charge the battery with maximum cur-
rent, while minimizing the increase in die temperature.
Input Sources
The MAX8922L operates from well-regulated DC
sources. The charger input voltage range is 4.45V to
7V. The device survives input voltages up to 30V with-
out damage to the IC. If the input voltage is greater
than 7.5V (typ), the IC stops charging. An appropriate
power supply must provide at least 4.2V plus the volt-
age drop across the internal-pass transistor when
sourcing the desired peak charging current.
V IN(MIN) > 4.2V + I FAST-CHARGE(MAX) x R ON
where R ON is the input-to-BAT resistance. Failure to
meet this requirement results in an incomplete charge
or increased charge time.
Recommended PCB Layout and Routing
Place all bypass capacitors for IN and BAT as close as
possible to the IC. Connect the battery to BAT as close
as possible to the IC to provide accurate battery volt-
age sensing. Provide a large copper ground plane to
allow the exposed pad to sink heat away from the
device. Make all high-current traces short and wide to
minimize voltage drops. A sample layout is available in
the MAX8922L Evaluation Kit to speed designs.
Typical Application Circuits
AC Adapter Charge
Figure 4 shows the MAX8922L as a Li+ battery charger
with an AC adapter. The MAX8922L detects the pres-
ence of an input supply resulting in POK pulled low.
Once POK is pulled low, the MAX8922L begins charg-
ing the battery when EN /SET is low or unconnected.
The system can program the charge current by EN /SET
pulses. By monitoring CHG , the system can detect the
top-off threshold and terminate the charge through
EN /SET. The MAX8922L also provides an overvoltage-
protected 4.94V LDO output to a low-voltage-rated USB
system input.
10
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| MAX892LEUA+T | IC SW P-CH HS 8-UMAX |
| MAX8934BETI+ | IC BATTERY CHARGER DUAL 28TQFN |
| MAX8934GETI+ | IC LI BATT CHARGER DUAL 28TQFN |
| MAX8939EWV+T | IC PWR MGMT HANDSETS 30WLP |
| MAX893LESA+T | IC SW P-CH HS 8-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX8925EWN+ | 制造商:Maxim Integrated Products 功能描述:MAX8925EWN+ |
| MAX8925EWN+T | 制造商:Maxim Integrated Products 功能描述:- Tape and Reel |
| MAX8929EWA+T | 制造商:Maxim Integrated Products 功能描述:STANDARD PRODUCTS - Tape and Reel 制造商:Maxim Integrated Products 功能描述:MAX8929EWA+T |
| MAX892LEUA | 功能描述:电源开关 IC - 配电 Current-Limited High-Side PCh Switch RoHS:否 制造商:Exar 输出端数量:1 开启电阻（最大值）:85 mOhms 开启时间（最大值）:400 us 关闭时间（最大值）:20 us 工作电源电压:3.2 V to 6.5 V 电源电流（最大值）: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOT-23-5 |
| MAX892LEUA+ | 功能描述:电源开关 IC - 配电 Current-Limited High-Side PCh Switch RoHS:否 制造商:Exar 输出端数量:1 开启电阻（最大值）:85 mOhms 开启时间（最大值）:400 us 关闭时间（最大值）:20 us 工作电源电压:3.2 V to 6.5 V 电源电流（最大值）: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOT-23-5 |
发布紧急采购，3分钟左右您将得到回复。