- 您现在的位置：买卖IC网 > PDF目录1850 > MAX8922LETB+T (Maxim Integrated Products)IC BATTERY CHARGER SGL 10TDFN PDF资料下载
参数资料
| 型号： | MAX8922LETB+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 7/15页 |
| 文件大小： | 0K |
| 描述： | IC BATTERY CHARGER SGL 10TDFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 功能： | 充电管理 |
| 电池化学： | 锂离子（Li-Ion） |
| 电源电压： | 0 V ~ 28 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-WFDFN 裸露焊盘 |
| 供应商设备封装： | 10-TDFN EP（3x2） |
| 包装： | 带卷 (TR) |
30V Li+ Linear Battery Charger
with GSM Test Mode in 3mm x 2mm TDFN
Detailed Description
The MAX8922L is designed to charge a single-cell Li+
battery from a DC source voltage between 4.45V and
7V, while V IN can withstand up to 30V. The fast-charge
current and top-off current thresholds are programma-
ble with EN /SET, SETI, and MIN.
Charger-Enable and Program Input
( EN /SET)
EN /SET is an active-low logic input that enables the
charger. Drive EN /SET high longer than 4ms to disable
the charger-control circuitry. If EN /SET is left uncon-
nected, an internal 2M ? pulldown resistor enables
400mA fast-charge current by default. The pulse pro-
gramming scheme shown in Table 1 and Figure 3 is
used to program the charge current and GSM test
mode. There are four different fast-charge current
states. Default fast-charge current state is 400mA
mode. More than three pulses are interpreted to 90mA
mode. After programming is locked, the MAX8922L
ignores pulses until the IC is disabled/enabled or input
power is cycled. Each fast-charge state is locked after
a 4ms logic-low is asserted on EN /SET, followed by
programming pulses. However, during default mode, if
EN /SET does not receive any pulses, the charger stays
in default mode unlocked indefinitely.
Debounce Timer
To prevent the MAX8922L from charging the battery
momentarily upon IN power-up with EN /SET held low, a
2ms (typ) debounce timer delays the charging loop
upon power-up. If EN /SET is logic-low or unconnected
(pulled down by an internal pulldown resistor) during IN
power-up, the charger starts charging the battery 2ms
after V UVLO < V IN < V OVP and V BAT + 250mV < V IN . If
EN /SET is logic-high during IN power-up, the charger
does not charge the battery.
Table 1. Charge-Current Pulse Settings
Soft-Start
To prevent input transients, the rate of change of the
charge current is limited when the charger is turned on
or changes its current compliance. It takes approxi-
mately 250μs (typ) (t SOFTSTART ) for the charger to go
from 0mA to the maximum fast-charge current.
Thermal-Limit Control
The MAX8922L features a thermal limit that reduces the
charge current when the die temperature exceeds
+105°C. As the temperature increases above +105°C,
the IC decreases the charge current by 28mA/°C.
Charge-Indicator Output ( CHG )
CHG is an open-drain output that indicates charger sta-
tus. CHG goes low during charging in prequalification
or fast-charge mode. The CHG internal open-drain
MOSFET turns off when the charge current reaches the
top-off threshold. The CHG status is latched after the
top-off threshold is reached. The latch can be reset as
follows:
? Disable and re-enable the MAX8922L.
? Input power is cycled.
? Battery-charge current increases greater than the
top-off threshold + hysteresis.
When the MAX8922L is used in conjunction with a
microprocessor, connect a pullup resistor between
CHG and the logic I/O voltage to indicate charge status
to the μP. Alternatively, CHG can sink 5mA or more for
an LED charge indicator.
CHARGE CURRENT
I BAT (mA)
DEFAULT
400mA
NUMBER OF PULSES + > 4ms
LOGIG-LOW
One
Two
Three
Four and more
FAST-CHARGE CURRENT SETTING
SETI, resistor programmable
90mA
2.3A (GSM test)
90mA
_______________________________________________________________________________________
7
相关PDF资料 |
PDF描述 |
|---|---|
| MAX892LEUA+T | IC SW P-CH HS 8-UMAX |
| MAX8934BETI+ | IC BATTERY CHARGER DUAL 28TQFN |
| MAX8934GETI+ | IC LI BATT CHARGER DUAL 28TQFN |
| MAX8939EWV+T | IC PWR MGMT HANDSETS 30WLP |
| MAX893LESA+T | IC SW P-CH HS 8-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX8925EWN+ | 制造商:Maxim Integrated Products 功能描述:MAX8925EWN+ |
| MAX8925EWN+T | 制造商:Maxim Integrated Products 功能描述:- Tape and Reel |
| MAX8929EWA+T | 制造商:Maxim Integrated Products 功能描述:STANDARD PRODUCTS - Tape and Reel 制造商:Maxim Integrated Products 功能描述:MAX8929EWA+T |
| MAX892LEUA | 功能描述:电源开关 IC - 配电 Current-Limited High-Side PCh Switch RoHS:否 制造商:Exar 输出端数量:1 开启电阻（最大值）:85 mOhms 开启时间（最大值）:400 us 关闭时间（最大值）:20 us 工作电源电压:3.2 V to 6.5 V 电源电流（最大值）: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOT-23-5 |
| MAX892LEUA+ | 功能描述:电源开关 IC - 配电 Current-Limited High-Side PCh Switch RoHS:否 制造商:Exar 输出端数量:1 开启电阻（最大值）:85 mOhms 开启时间（最大值）:400 us 关闭时间（最大值）:20 us 工作电源电压:3.2 V to 6.5 V 电源电流（最大值）: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOT-23-5 |
发布紧急采购，3分钟左右您将得到回复。