- 您现在的位置：买卖IC网 > PDF目录5055 > MAX8982EWO+T (Maxim Integrated Products)IC PWR MGMT ICERA E400 42WLP PDF资料下载
参数资料
| 型号： | MAX8982EWO+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 38/73页 |
| 文件大小： | 0K |
| 描述： | IC PWR MGMT ICERA E400 42WLP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,000 |
| 应用： | 电源，ICERA E400，E450 |
| 输入电压： | 4.1 V ~ 5.5 V |
| 输出数： | 13 |
| 输出电压： | 可编程 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 42-WFBGA，WLCSP |
| 供应商设备封装： | 42-WLP |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页当前第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页
MAX8982A/MAX8982P/MAX8982X
Power-Management ICs for
ICERA E400 Platform
Ramp-Up/Down Slope Control on BUCK1
BUCK1 uses a controlled ramp rate when it is enabled
and when changing between output voltage settings.
Four programmable slew rates are available for BUCK1.
The default value is 12.5mV/ F s (Table 4). The same slew
rate is applied for ramp-up/down.
Setting the Output Voltage on BUCK2
The BUCK2 output voltage is fixed at 1.8V. No program-
mable output is available.
Setting the Output Voltage on BUCK3
The BUCK3 default output is 3.2V. The BUCK3 output
voltage is programmable from 2.9V to 3.65V in 50mV
increments through I 2 C. BUCK3 is only available on the
MAX8982A/MAX8982P.
BUCK4 Step-Down Converter
for PA (Power Amplifier)
BUCK4 is a 2MHz fixed-frequency PWM step-down
converter, typically used to supply the power amplifier
(PA). The BUCK4 load capability is 1.8A. BUCK4 is only
available on the MAX8982A/MAX8982P.
Setting the Output Voltage on BUCK4
The default output voltage is 3.4V. The BUCK4 output
voltage is programmable between 3.0V and 3.75V in
50mV increments through I 2 C.
Linear Regulators
All linear regulators are designed for low-drop, low noise,
high PSRR, and low quiescent current to minimize power
consumption. If the input voltage is above UVLO thresh-
old and power-on is logic-high, the default linear regula-
tor (LDO3) turns on. The other LDOs are turned on and
off by the baseband processor through the I 2 C interface
or PWR_REQ control signal. All LDO output voltages are
programmable through the I 2 C interface within option
voltages.
Table 4. BUCK1 Ramp-Up/Down Slope
Control Settings
Reference Bypass (REFBP)
The reference bypass is for low noise filtering only and
must not be loaded. Bypass REFBP with a 0.1 F F ceramic
capacitor. The REFBP voltage is 0.8V (typ). Do not use
REFBP to provide power to external circuitry.
Thermal Overload Protection
If the internal die temperature of any LDOs or step-
down regulators reaches +160 N C, the ICs shut down the
regulator locally. The regulator is reenabled after it cools
by 10 N C. The ICs also contain a single +125 N C thermal
detector located in the center of the die. When the tem-
perature at the center of the die exceeds +125 N C, this
detector triggers and activates an interrupt.
Undervoltage Lockout (UVLO)
The ICs monitor the voltage at the IN1_ power input.
When this voltage drops below 3.5V (MAX8982A) or 2.4V
(MAX8982P/MAX8982X), the ICs shut down. The ICs
turn on when this voltage rises above 3.8V (MAX8982A)
or 2.7V (MAX8982P/MAX8982X) and EN is high. After a
UVLO event, all registers are reset to their POR value.
Overvoltage Protection (OVP)
If the voltage on the IN1_ or IN4 inputs exceeds 5.75V
(typ), the ICs shut down. When the supply voltage
returns to within the valid operating range and EN is
high, the ICs turn on and go through a normal power-up
sequence. All registers are reset to their default power-
on reset (POR) value.
Power-On Reset (POR)
Power-on reset (POR) for I 2 C occurs when the ICs turn
off due to UVLO, OVP, or EN = low. This condition puts
the IC into shutdown and then clears all previously pro-
grammed output voltages in the internal registers.
The programmed values in BUCK1DVS1 and
BUCK1DVS2 are also reset to their defaults when
PWR_REQ goes low in normal operation mode.
DOWN
SLOPE
RASD1[1]
0
RASD1[0]
0
SLEW RATE (mV/μs)
5
CONTROL
0
1
1
0
10
12.5 (default)
V BUCK1
UP SLOPE
CONTROL
38
1
1
25
Figure 8. BUCK1 Ramp-Up/Down Slope Control
Maxim Integrated
相关PDF资料 |
PDF描述 |
|---|---|
| P1330R-273K | INDUCTOR POWER 27.0UH SMD |
| X5649S14-2.7T1 | IC SUPERVISOR CPU 64K EE 14-SOIC |
| GSM22DSES | CONN EDGECARD 44POS .156 EYELET |
| ABB40DHRN | CONN CARD EXTEND 80POS .050" |
| X5649S14IT1 | IC SUPERVISOR CPU 64K EE 14-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX8982MEWO+T | 功能描述:PMIC 解决方案 PMIC for ICERA E400/E450 Platform RoHS:否 制造商:Texas Instruments 安装风格:SMD/SMT 封装 / 箱体:QFN-24 封装:Reel |
| MAX8982PEWO+T | 功能描述:PMIC 解决方案 PMIC for ICERA E400/E450 Platform RoHS:否 制造商:Texas Instruments 安装风格:SMD/SMT 封装 / 箱体:QFN-24 封装:Reel |
| MAX8982XEWO+T | 制造商:Maxim Integrated Products 功能描述:POWER MANAGEMENT IC FOR ICERA E400/E450 PLATFORM-MINI CARD - Tape and Reel |
| MAX8986EVKIT+ | 制造商:Maxim Integrated Products 功能描述:PMIC FOR BROADCOM BB ATHENA - Boxed Product (Development Kits) |
| MAX8986EWG+ | 制造商:Maxim Integrated Products 功能描述:POWER MANAGEMENT IC FOR CELL PHONE |
发布紧急采购，3分钟左右您将得到回复。