- 您现在的位置：买卖IC网 > PDF目录2091 > MAX9726AETP+T (Maxim Integrated Products)IC AMP AUDIO .124W STER 20TQFN PDF资料下载
参数资料
| 型号： | MAX9726AETP+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 3/24页 |
| 文件大小： | 0K |
| 描述： | IC AMP AUDIO .124W STER 20TQFN |
| 标准包装： | 2,500 |
| 系列： | DirectDrive® |
| 类型： | AB 类 |
| 输出类型： | 耳机，2-通道（立体声） |
| 在某负载时最大输出功率 x 通道数量： | 124mW x 2 @ 16 欧姆 |
| 电源电压： | 2.7 V ~ 5.5 V |
| 特点： | 低音增强模式，消除爆音，I²C，静音，短路和热保护，关机，音量控制 |
| 安装类型： | 表面贴装 |
| 供应商设备封装： | 20-TQFN-EP（4x4） |
| 封装/外壳： | 20-WFQFN 裸露焊盘 |
| 包装： | 带卷 (TR) |
Charge Pump
The MAX9726 features a low-noise charge pump. The
610kHz switching frequency is well beyond the audio
range, and does not interfere with the audio signals.
This enables the MAX9726 to achieve an SNR of
102dB. The switch drivers feature a controlled switch-
ing speed that minimizes noise generated by turn-on
and turn-off transients. Limiting the switching speed of
the charge pump also minimizes di/dt noise caused by
the parasitic bond wire and trace inductance.
Click-and-Pop Suppression
In conventional single-supply headphone amplifiers,
the output coupling capacitor is a major contributor of
audible clicks and pops. The amplifier charges the
coupling capacitor to its output bias voltage at startup.
During shutdown, the capacitor is discharged. This
charging and discharging results in a DC shift across
the capacitor, which appears as an audible transient at
the headphone speaker. Since the MAX9726 head-
phone amplifier does not require output-coupling
capacitors, no audible transients occur.
Additionally, the MAX9726 features extensive click-and-
pop suppression that eliminates any audible transient
sources internal to the device. The Power-Up/Power-
Down graph in the
Typical Operating Characteristics
shows that there are minimal transients at the output
upon startup or shutdown.
In most applications, the preamplifier driving the
MAX9726 has a DC bias of typically half the supply.
The input-coupling capacitor is charged to the pream-
plifier’s bias voltage through the MAX9726’s input resis-
tor (RIN) during startup. The resulting voltage shift
across the capacitor creates an audible click-and-pop.
Delay the rise of SHDN by at least four time constants
(4 x RIN x CIN) relative to the start of the preamplifier to
avoid clicks/pops caused by the input filter.
Shutdown
The MAX9726 features a 8A, low-power shutdown
mode that reduces quiescent current consumption and
extends battery life. Shutdown is controlled by a hard-
ware and software interface. Driving the SHDN input low
disables the drive amplifiers, bias circuitry, charge
pump, and sets the headphone amplifier output resis-
tance to 50kΩ. Similarly, the MAX9726 enters shutdown
when bit seven (B7) in the control register is set to 0 (see
the
Command Register section). SHDN and B7 must be
high to enable the MAX9726. The I2C/SMBus interface is
active and the contents of the command register are not
affected when in shutdown. This allows the master to
write to the MAX9726 while in shutdown.
BassMax (Bass Boost)
Typical headphones do not have a flat-frequency
response. The small physical size of the diaphragm
does not allow the headphone speaker to efficiently
reproduce low frequencies. This physical limitation
results in attenuated bass response. The MAX9726
includes a bass-boost feature that compensates for the
headphone’s poor bass response by increasing the
amplifier gain at low frequencies.
The DirectDrive output of the MAX9726 has more head-
room than typical single-supply headphone amplifiers.
This additional headroom allows boosting the bass fre-
quencies without the output signal clipping.
Program the BassMax gain and cutoff frequency with
external components connected between OUT_ and
BM_ (see the
Gain-Setting Components section and the
Functional Diagram/Typical Operating Circuit). Use the
I2C-compatible interface to program the command reg-
ister to enable/disable the BassMax circuit.
BM_ is connected to the noninverting input of the out-
put amplifier when BassMax is enabled. BM_ is pulled
to SGND when BassMax is disabled. The typical appli-
cation of the BassMax circuit involves feeding a low-
pass version of the output signal back to the amplifier.
This is realized using positive feedback from OUT_ to
BM_. Figure 2 shows the connections needed to imple-
ment BassMax.
MAX9726
DirectDrive, Headphone Amplifier with
BassMax, I2C, Volume and Gain Control
______________________________________________________________________________________
11
C3
R2
R1
TO HEADPHONE
SPEAKER
R
OUT_
BM_
FROM
ATTENUATOR
STAGE
MAX9726
BassMax
ENABLE
Figure 2. BassMax External Connections
相关PDF资料 |
PDF描述 |
|---|---|
| MAX9727EEP+T | IC AMP AUDIO QUAD AB DIFF 20QSOP |
| MAX9728AETC+T | IC AMP AUDIO .06W STER AB 12TQFN |
| MAX9729ETI+T | IC AMP AUDIO .052W STER 28TQFN |
| MAX9730ETI+T | IC AMP AUDIO PWR 2.4W G 28TQFN |
| MAX9736AETJ/V+ | IC AMP MONO/STER CLASS D 32TQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX9726BEBP+ | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| MAX9726BEBP+T | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| MAX9726BETP+ | 功能描述:音频放大器 Integrated Circuits (ICs) RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| MAX9726BETP+T | 功能描述:音频放大器 Integrated Circuits (ICs) RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| MAX9726EVKIT+ | 功能描述:放大器 IC 开发工具 RoHS:否 制造商:International Rectifier 产品:Demonstration Boards 类型:Power Amplifiers 工具用于评估:IR4302 工作电源电压:13 V to 23 V |
发布紧急采购，3分钟左右您将得到回复。