- 您现在的位置：买卖IC网 > PDF目录10262 > MAX9761EUI+T (Maxim Integrated Products)IC AMP AUDIO PWR 3W STER 28TSSOP PDF资料下载
参数资料
| 型号： | MAX9761EUI+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 5/31页 |
| 文件大小： | 0K |
| 描述： | IC AMP AUDIO PWR 3W STER 28TSSOP |
| 标准包装： | 2,500 |
| 类型： | AB 类 |
| 输出类型： | 2-通道（立体声）带立体声耳机 |
| 在某负载时最大输出功率 x 通道数量： | 3W x 2 @ 3 欧姆; 200mW x 2 @ 16 欧姆 |
| 电源电压： | 4.5 V ~ 5.5 V |
| 特点： | 消除爆音，输入多路复用器，静音，关机，热保护， |
| 安装类型： | 表面贴装 |
| 供应商设备封装： | 28-TSSOP 裸露焊盘 |
| 封装/外壳： | 28-SOIC（0.173"，4.40mm 宽）裸露焊盘 |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页当前第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页
MAX9760–MAX9763
Stereo 3W Audio Power Amplifiers with
Headphone Drive and Input Mux
______________________________________________________________________________________
13
When configured as a headphone (single-ended) ampli-
fier, the slave amplifier is disabled, muting the speaker
and the main amplifier drives the headphone. The
MAX9760–MAX9763 can deliver 3W of continuous aver-
age power into a 3
load with less than 1% THD+N in
speaker mode, and 200mW of continuous average
power into a 16
load with less than 1% THD+N in
headphone mode. These devices also feature thermal
overload protection.
Mono Mode
The MAX9762/MAX9763 are 3W mono speaker ampli-
fiers, 200mW stereo headphone amplifiers, and a
mixer/attenuator (see the MAX9762/MAX9763 Functional
Diagram). In speaker (mono) mode, the mixer/attenuator
combines the two stereo inputs (INL_ and INR_) and
attenuates the resultant signal by a factor of 2. This
allows for full reproduction of a stereo signal through a
single speaker, while maintaining optimum headroom.
The resistor connected between GAINM and OUTR+,
sets the gain of the devices in speaker mode (see the
MAX9762 Functional Diagram). This allows the speaker
amplifier to have a different gain and feedback network
from the headphone amplifier.
BIAS
These devices operate from a single 5V supply, and
feature an internally generated, power-supply indepen-
dent, common-mode bias voltage of 2.5V referenced to
GND. BIAS provides both click-and-pop suppression
and sets the DC bias level for the audio outputs. BIAS
is internally connected to the noninverting input of each
speaker amplifier (see Typical Application Circuit/
Functional Diagram). Choose the value of the bypass
capacitor as described in the BIAS Capacitor section.
No external load should be applied to BIAS. Any load
lowers the BIAS voltage, affecting the overall perfor-
mance of the device.
Input Multiplexer
Each amplifier features a 2:1 input multiplexer, allowing
input selection between two stereo sources. Both multi-
plexers are controlled by bit 1 in the control register
(MAX9760/MAX9762) or by the IN1/2 pin (MAX9761/
MAX9763). A logic low selects input IN_1 and a logic
high selects input IN_2.
The input multiplexer can also be used to further
expand the number of gain options available from the
MAX9760–MAX9763 family. Connecting the audio
source to the device through two different input resis-
tors (Figure 1) increases the number of gain options
from two to four (MAX9760/MAX9761) and from three to
six (MAX9762/MAX9763). Additionally, the input multi-
plexer allows a speaker equalization network to be
switched into the speaker signal path. This is typically
useful in optimizing acoustic response from speakers
with small physical dimensions.
Headphone Sense Enable
The HPS pin is enabled by HPS_EN (MAX9762/
MAX9763) or the HPSD bit (MAX9760/MAX9761).
HPSD or HPS_EN determines whether the device is in
automatic detection mode or fixed mode operation (see
Tables 1a and 1b).
Headphone Sense Input (HPS)
A voltage on HPS less than 0.7 VDD sets the device
to speaker mode. A voltage greater than 0.9 VDD dis-
ables the inverting bridge amplifier (OUT_-), which
mutes the speaker amplifier and sets the device into
headphone mode.
For automatic headphone detection, connect HPS to the
control pin of a 3-wire headphone jack as shown in
Figure 2. With no headphone present, the resistive volt-
age-divider created by R1 and R2 sets the voltage on
HPS to be less than 0.7 VDD, setting the device to
speaker mode and the gain setting defaults to GAINA
(MAX9760/MAX9762). When a headphone plug is insert-
ed into the jack, the control pin is disconnected from the
tip contact, and HPS is pulled to VDD through R1, setting
the device into headphone mode and the gain-setting
defaults to GAINB (MAX9760/MAX9762) (see Gain
Select section). Place a resistor in series with the control
pin and HPS (R3) to prevent any audio signal from cou-
pling into HPS when the device is in speaker mode.
Shutdown
The MAX9760–MAX9763 feature a 10A, low-power
shutdown mode that reduces quiescent current con-
sumption and extends battery life. The drive amplifiers
and bias circuitry are disabled, the amplifier outputs
(OUT_) go high impedance, and BIAS is driven to
MAX9760
AUDIO
INPUT
15k
30k
IN_1
IN_2
Figure 1. Using the Input Multiplexer for Gain Setting
相关PDF资料 |
PDF描述 |
|---|---|
| CXS3102A188P | CONN RCPT 8POS PNL MNT PIN |
| TB6M | CONN RCPT CORD MINI 6POS MALE |
| MAX9763EUI+T | IC AMP AUDIO PWR 3W MONO 28TSSOP |
| LTC1854IG#TRPBF | IC ADC 12BIT 8CH 100KSPS 28SSOP |
| MAX9765ETJ+T | IC AMP AUDIO .75W STER AB 32TQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX9761EVKIT | 功能描述:放大器 IC 开发工具 RoHS:否 制造商:International Rectifier 产品:Demonstration Boards 类型:Power Amplifiers 工具用于评估:IR4302 工作电源电压:13 V to 23 V |
| MAX9762ETI | 功能描述:音频放大器 RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| MAX9762ETI+ | 功能描述:音频放大器 Integrated Circuits (ICs) RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| MAX9762ETI+T | 功能描述:音频放大器 Integrated Circuits (ICs) RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| MAX9762ETI-T | 功能描述:音频放大器 RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。