- 您现在的位置：买卖IC网 > PDF目录2091 > MAX9763ETI+T (Maxim Integrated Products)IC AMP AUDIO PWR 3W MONO 28TQFN PDF资料下载
参数资料
| 型号： | MAX9763ETI+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 6/31页 |
| 文件大小： | 0K |
| 描述： | IC AMP AUDIO PWR 3W MONO 28TQFN |
| 标准包装： | 2,500 |
| 类型： | AB 类 |
| 输出类型： | 1-通道（单声道），带立体声耳机 |
| 在某负载时最大输出功率 x 通道数量： | 3W x 1 @ 3 欧姆; 200mW x 2 @ 16 欧姆 |
| 电源电压： | 4.5 V ~ 5.5 V |
| 特点： | 消除爆音，输入多路复用器，静音，关机，热保护， |
| 安装类型： | 表面贴装 |
| 供应商设备封装： | 28-TQFN-EP（5x5） |
| 封装/外壳： | 28-WFQFN 裸露焊盘 |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页当前第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页
MAX9760–MAX9763
Stereo 3W Audio Power Amplifiers with
Headphone Drive and Input Mux
14
______________________________________________________________________________________
GND. Driving SHDN low places the devices into shut-
down mode, disables the interface, and resets the I2C
registers to a default state. A logic high on SHDN
enables the devices.
MAX9760/MAX9762 Software Shutdown
A logic high on bit 0 of the SHDN register places the
MAX9760/MAX9762 in shutdown mode. A logic low
enables the device. The digital section of the
MAX9760/MAX9762 remains active when the device is
shut down through the interface. All devices feature a
logic low on the SHDN input.
MUTE
All devices feature a mute mode. When the device is
muted, the input is disconnected from the amplifiers.
MUTE does not shut down the device.
MAX9760/MAX9762 MUTE
The MAX9760/MAX9762 MUTE mode is selected by
writing to the MUTE register (see the Command Byte
Definitions section). The left and right channels can be
independently muted.
MAX9761/MAX9763 MUTE
The MAX9761/MAX9763 feature an active-high MUTE
input that mutes both channels.
Click-and-Pop Suppression
The MAX9760–MAX9763 feature Maxim’s comprehen-
sive click-and-pop suppression. During startup and
shutdown, the common-mode bias voltage of the ampli-
fiers is slowly ramped to and from the DC bias point
using an S-shaped waveform. In headphone mode, this
waveform shapes the frequency spectrum, minimizing
the amount of audible components present at the head-
phone. In speaker mode, the BTL amplifiers start up in
the same fashion as in headphone mode. When enter-
ing shutdown, both amplifier outputs ramp to GND
quickly
and
simultaneously.
The
MAX9760–
MAX9763 can also be connected to a standby power
source that ensures that the device undergoes its full
shutdown cycle even after power has been removed.
Standby Power Supply (SVDD)
The MAX9760–MAX9763 feature a system that provides
clickless power-down when power is inadvertently
removed from the device. SVDD is an optional sec-
ondary supply that powers the device through its shut-
down cycle when VDD is removed. During this cycle,
the amplifier output DC level slowly ramps to GND,
ensuring clickless power-down. If clickless power-down
is required, connect SVDD to either a secondary power
supply that is always on, or connect a reservoir capaci-
tor from SVDD to GND. SVDD does not need to be con-
nected to either a secondary power supply or reservoir
capacitor for normal device operation. If click-and-pop
suppression during power-down is not required, con-
nect SVDD to VDD directly.
MAX9760–
MAX9763
R3
47k
Ω
R1
680k
Ω
R2
10k
Ω
HPS
VDD
OUTL+
OUTR+
Figure 2. HPS Configuration Circuit
INPUTS
HPSD
HPS
SPKR/HP
MODE
MAX9760
GAIN
PATH*
MAX9762
GAIN
PATH*
0
X
BTL
A
M
01
X
SE
B
1
X
0
BTL
A or B
M
1
X
1
SE
A or B
Table 1a. HPS Setting (MAX9760/MAX9761)
INPUTS
HPSEN
HPS
MODE
MAX9761
GAIN PATH*
MAX9763
GAIN PATH*
0
X
BTL
A or B
M
1
0
BTL
A or B
M
1
SE
A or B
Table 1b. HPS Setting (MAX9762/MAX9763)
*Note:
A – GAINA path selected
B – GAINB path selected
M – GAINM path selected
A or B – Gain path selected by GAINAB control bit in register
02h
*Note:
A or B – Gain path selected by external GAINAB
M – GAINM path selected
相关PDF资料 |
PDF描述 |
|---|---|
| MAX9767ETJ+T | IC AMP AUDIO .75W STER AB 32TQFN |
| MAX9768ETG+T | IC AMP AUDIO 10W MONO D 24TQFN |
| MAX9770EUI+T | IC AMP AUDIO 1.2W MONO D 28TSSOP |
| MAX9773EBP+TG45 | IC AMP AUDIO PWR 1.8W D 20UCSP |
| MAX9776ETJ+T | IC AMP AUDIO PWR 1.5W D 32TQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX9763EUI | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| MAX9763EUI+ | 功能描述:IC AMP AUDIO PWR 3W MONO 28TSSOP RoHS:是 类别:集成电路 (IC) >> 线性 - 音頻放大器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:DirectDrive® 类型:H 类 输出类型:耳机，2-通道（立体声） 在某负载时最大输出功率 x 通道数量:35mW x 2 @ 16 欧姆 电源电压:1.62 V ~ 1.98 V 特点:I²C，麦克风，静音，短路保护，音量控制 安装类型:表面贴装 供应商设备封装:25-WLP（2.09x2.09） 封装/外壳:25-WFBGA，WLCSP 包装:带卷 (TR) |
| MAX9763EUI+T | 功能描述:IC AMP AUDIO PWR 3W MONO 28TSSOP RoHS:是 类别:集成电路 (IC) >> 线性 - 音頻放大器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:DirectDrive® 类型:H 类 输出类型:耳机，2-通道（立体声） 在某负载时最大输出功率 x 通道数量:35mW x 2 @ 16 欧姆 电源电压:1.62 V ~ 1.98 V 特点:I²C，麦克风，静音，短路保护，音量控制 安装类型:表面贴装 供应商设备封装:25-WLP（2.09x2.09） 封装/外壳:25-WFBGA，WLCSP 包装:带卷 (TR) |
| MAX9765ETJ | 功能描述:音频放大器 RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| MAX9765ETJ+ | 功能描述:音频放大器 Integrated Circuits (ICs) RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。