- 您现在的位置：买卖IC网 > PDF目录10268 > MAX9777ETI+T (Maxim Integrated Products)IC AMP AUDIO PWR 2.6W AB 28TQFN PDF资料下载
参数资料
| 型号： | MAX9777ETI+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 10/27页 |
| 文件大小： | 0K |
| 描述： | IC AMP AUDIO PWR 2.6W AB 28TQFN |
| 标准包装： | 2,500 |
| 类型： | AB 类 |
| 输出类型： | 2-通道（立体声）带立体声耳机 |
| 在某负载时最大输出功率 x 通道数量： | 2.6W x 2 @ 4 欧姆; 200mW x 2 @ 16 欧姆 |
| 电源电压： | 4.5 V ~ 5.5 V |
| 特点： | 消除爆音，I²C，输入多路复用器，静音，关机，热保护 |
| 安装类型： | 表面贴装 |
| 供应商设备封装： | 28-TQFN-EP（5x5） |
| 封装/外壳： | 28-WFQFN 裸露焊盘 |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页当前第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页
MAX9777/MAX9778
Stereo 3W Audio Power Amplifiers with
Headphone Drive and Input Mux
18
_
__
_
Applications Information
BTL Speaker Amplifiers
The MAX9777/MAX9778 feature speaker amplifiers
designed to drive a load differentially, a configuration
referred to as bridge-tied load (BTL). The BTL configu-
ration (Figure 8) offers advantages over the single-
ended configuration, where one side of the load is
connected to ground. Driving the load differentially
doubles the output voltage compared to a single-
ended amplifier under similar conditions. Thus, the
devices’ differential gain is twice the closed-loop gain
of the input amplifier. The effective gain is given by:
Substituting 2 x VOUT(P-P) for VOUT(P-P) into the follow-
ing equations yields four times the output power due to
doubling of the output voltage:
Since the differential outputs are biased at midsupply,
there is no net DC voltage across the load. This elimi-
nates the need for DC-blocking capacitors required for
single-ended amplifiers. These capacitors can be large
and expensive, consume board space, and degrade
low-frequency performance.
When the MAX9777 is configured to automatically detect
the presence of a headphone jack, the device defaults to
gain setting A when the device is in speaker mode.
Single-Ended Headphone Amplifier
The MAX9777/MAX9778 can be configured as single-
ended headphone amplifiers through software or by
sensing the presence of a headphone plug (HPS). In
headphone mode, the inverting output of the BTL
amplifier is disabled, muting the speaker. The gain is
1/2 that of the device in speaker mode, and the output
power is reduced by a factor of 4.
In headphone mode, the load must be capacitively
coupled to the device, blocking the DC bias voltage
from the load (see the
Typical Application Circuits).
Power Dissipation and Heat Sinking
Under normal operating conditions, the MAX9777/
MAX9778 can dissipate a significant amount of power.
The maximum power dissipation for each package is
given in the
Absolute Maximum Ratings section under
Continuous Power Dissipation or can be calculated by
the following equation:
where TJ(MAX) is +150°C, TA is the ambient tempera-
ture, and
θJA is the reciprocal of the derating factor in
°C/W as specified in the
Absolute Maximum Ratings
section. For example,
θJA of the TQFN package is
+29°C/W.
The increase in power delivered by the BTL configura-
tion directly results in an increase in internal power dis-
sipation over the single-ended configuration. The
maximum power dissipation for a given VDD and load is
given by the following equation:
If the power dissipation for a given application exceeds
the maximum allowed for a given package, either reduce
VDD, increase load impedance, decrease the ambient
temperature, or add heatsinking to the device. Large
output, supply, and ground PC board traces improve the
maximum power dissipation in the package.
Thermal-overload protection limits total power dissipa-
tion in these devices. When the junction temperature
exceeds +160°C, the thermal-protection circuitry dis-
ables the amplifier output stage. The amplifiers are
enabled once the junction temperature cools by 15°C.
This results in a pulsing output under continuous ther-
mal-overload conditions as the device heats and cools.
P
V
R
DISS MAX
DD
L
() =
2
π
P
TT
DISSPKG MAX
J MAX
A
JA
()
=
θ
V
P
V
R
RMS
OUT P P
OUT
RMS
L
=
()
22
2
A
R
VD
F
IN
=×
2
+1
VOUT(P-P)
2 x VOUT(P-P)
VOUT(P-P)
-1
Figure 8. Bridge-Tied Load Configuration
相关PDF资料 |
PDF描述 |
|---|---|
| D38999/20KE6SNLC | CONN HSG RCPT 6POS WALL MT SCKT |
| MS27473T24B4SCLC | CONN HSG PLUG 56POS STRGHT SCKT |
| LTC2414IGN#TR | IC ADC 8CH 24BIT DIFFINPUT28SSOP |
| MS27473T24B4SBLC | CONN HSG PLUG 56POS STRGHT SCKT |
| D38999/26JJ4PALC | CONN HSG PLUG 56POS STRGHT PINS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX9778ETI+ | 功能描述:音频放大器 Integrated Circuits (ICs) RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| MAX9778ETI+T | 功能描述:音频放大器 Integrated Circuits (ICs) RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| MAX9779ETI+ | 功能描述:音频放大器 Integrated Circuits (ICs) RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| MAX9779ETI+T | 功能描述:音频放大器 Integrated Circuits (ICs) RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| MAX977EEE | 功能描述:校验器 IC 3V/5V Dual-Speed Comparator RoHS:否 制造商:STMicroelectronics 产品: 比较器类型: 通道数量: 输出类型:Push-Pull 电源电压-最大:5.5 V 电源电压-最小:1.1 V 补偿电压（最大值）:6 mV 电源电流（最大值）:1350 nA 响应时间: 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:SC-70-5 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。