- 您现在的位置：买卖IC网 > PDF目录10268 > MAX9777ETI+T (Maxim Integrated Products)IC AMP AUDIO PWR 2.6W AB 28TQFN PDF资料下载
参数资料
| 型号： | MAX9777ETI+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 7/27页 |
| 文件大小： | 0K |
| 描述： | IC AMP AUDIO PWR 2.6W AB 28TQFN |
| 标准包装： | 2,500 |
| 类型： | AB 类 |
| 输出类型： | 2-通道（立体声）带立体声耳机 |
| 在某负载时最大输出功率 x 通道数量： | 2.6W x 2 @ 4 欧姆; 200mW x 2 @ 16 欧姆 |
| 电源电压： | 4.5 V ~ 5.5 V |
| 特点： | 消除爆音，I²C，输入多路复用器，静音，关机，热保护 |
| 安装类型： | 表面贴装 |
| 供应商设备封装： | 28-TQFN-EP（5x5） |
| 封装/外壳： | 28-WFQFN 裸露焊盘 |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页当前第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页
MAX9777/MAX9778
Stereo 3W Audio Power Amplifiers with
Headphone Drive and Input Mux
_
__
_
15
Early STOP Conditions
The MAX9777 recognizes a STOP condition at any
point during the transmission except if a STOP condi-
tion occurs in the same high pulse as a START condi-
tion (Figure 5). This condition is not a legal I2C format;
at least one clock pulse must separate any START and
STOP condition.
REPEATED START Conditions
A REPEATED START (Sr) condition may indicate a
change of data direction on the bus. Such a change
occurs when a command word is required to initiate a
read operation. Sr may also be used when the bus
master is writing to several I2C devices and does not
want to relinquish control of the bus. The MAX9777 ser-
ial interface supports continuous write operations with
or without an Sr condition separating them. Continuous
read operations require Sr conditions because of the
change in direction of data flow.
Acknowledge Bit (ACK)
The acknowledge bit (ACK) is the ninth bit attached to
any 8-bit data word. The receiving device always gen-
erates ACK. The MAX9777 generates an ACK when
receiving an address or data by pulling SDA low during
the night clock period. When transmitting data, the
MAX9777 waits for the receiving device to generate an
ACK. Monitoring ACK allows for detection of unsuc-
cessful data transfers. An unsuccessful data transfer
occurs if a receiving device is busy or if a system fault
has occurred. In the event of an unsuccessful data
transfer, the bus master should reattempt communica-
tion at a later time.
Slave Address
The bus master initiates communication with a slave
device by issuing a START condition followed by a 7-bit
slave address (Figure 6). When idle, the MAX9777
waits for a START condition followed by its slave
address. The LSB of the address word is the
Read/Write (R/W) bit. R/W indicates whether the master
is writing to or reading from the MAX9777 (R/W = 0
selects the write condition, R/W = 1 selects the read
condition). After receiving the proper address, the
MAX9777 issues an ACK by pulling SDA low for one
clock cycle.
The MAX9777 has a factory-/user-programmed
address. Address bits A6–A2 are preset, while A0 and
A1 is set by ADD. Connect ADD to either VDD, GND,
SCL, or SDA to change the last 2 bits of the slave
address (Table 2).
SCL
SDA
STOP
START
SCL
SDA
ILLEGAL
STOP
START
LEGAL STOP CONDITION
ILLEGAL EARLY STOP CONDITION
Figure 5. Early STOP Condition
S
A6A5A4A3A2A1A0
R/W
Figure 6. Slave Address Byte Definition
ADD CONNECTION
I
2C ADDRESS
GND
100 1000
VDD
100 1001
SDA
100 1010
SCL
100 1011
Table 2. MAX9777 I2C Slave Addresses
相关PDF资料 |
PDF描述 |
|---|---|
| D38999/20KE6SNLC | CONN HSG RCPT 6POS WALL MT SCKT |
| MS27473T24B4SCLC | CONN HSG PLUG 56POS STRGHT SCKT |
| LTC2414IGN#TR | IC ADC 8CH 24BIT DIFFINPUT28SSOP |
| MS27473T24B4SBLC | CONN HSG PLUG 56POS STRGHT SCKT |
| D38999/26JJ4PALC | CONN HSG PLUG 56POS STRGHT PINS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX9778ETI+ | 功能描述:音频放大器 Integrated Circuits (ICs) RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| MAX9778ETI+T | 功能描述:音频放大器 Integrated Circuits (ICs) RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| MAX9779ETI+ | 功能描述:音频放大器 Integrated Circuits (ICs) RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| MAX9779ETI+T | 功能描述:音频放大器 Integrated Circuits (ICs) RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| MAX977EEE | 功能描述:校验器 IC 3V/5V Dual-Speed Comparator RoHS:否 制造商:STMicroelectronics 产品: 比较器类型: 通道数量: 输出类型:Push-Pull 电源电压-最大:5.5 V 电源电压-最小:1.1 V 补偿电压（最大值）:6 mV 电源电流（最大值）:1350 nA 响应时间: 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:SC-70-5 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。