- 您现在的位置：买卖IC网 > PDF目录10268 > MAX9777ETI+T (Maxim Integrated Products)IC AMP AUDIO PWR 2.6W AB 28TQFN PDF资料下载
参数资料
| 型号： | MAX9777ETI+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 4/27页 |
| 文件大小： | 0K |
| 描述： | IC AMP AUDIO PWR 2.6W AB 28TQFN |
| 标准包装： | 2,500 |
| 类型： | AB 类 |
| 输出类型： | 2-通道（立体声）带立体声耳机 |
| 在某负载时最大输出功率 x 通道数量： | 2.6W x 2 @ 4 欧姆; 200mW x 2 @ 16 欧姆 |
| 电源电压： | 4.5 V ~ 5.5 V |
| 特点： | 消除爆音，I²C，输入多路复用器，静音，关机，热保护 |
| 安装类型： | 表面贴装 |
| 供应商设备封装： | 28-TQFN-EP（5x5） |
| 封装/外壳： | 28-WFQFN 裸露焊盘 |
| 包装： | 带卷 (TR) |
第1页第2页第3页当前第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页
MAX9777/MAX9778
Stereo 3W Audio Power Amplifiers with
Headphone Drive and Input Mux
12
_
__
_
Detailed Description
The MAX9777/MAX9778 feature 3W BTL speaker
amplifiers, 200mW headphone amplifiers, input multi-
plexers, headphone sensing, and comprehensive click-
and-pop suppression. The MAX9777/MAX9778 are
stereo BTL/headphone amplifiers. The MAX9777 is
controlled through an I2C-compatible, 2-wire serial
interface. The MAX9778 is controlled through five logic
inputs: MUTE, SHDN, HPS_EN, GAINA/B, and IN1/2
(see the
Selector Guide). The MAX9777/MAX97778 fea-
ture exceptional PSRR (100dB at 1kHz), allowing these
devices to operate from noisy digital supplies without
the need for a linear regulator.
The speaker amplifiers use a BTL configuration. The
signal path is composed of an input amplifier and an
output amplifier. Resistor RIN sets the input amplifier’s
gain, and resistor RF sets the output amplifier’s gain.
The output of these two amplifiers serves as the input to
a slave amplifier configured as an inverting unity-gain
follower. This results in two outputs, identical in magni-
tude, but 180° out of phase. The overall gain of the
speaker amplifiers is twice the product of the two
amplifier gains (see the
Gain-Setting Resistors section).
A feature of this architecture is that there is no phase
inversion from input to output.
When configured as a headphone (single-ended) ampli-
fier, the slave amplifier is disabled, muting the speaker
and the main amplifier drives the headphone. The
MAX9777/MAX9778 can deliver 3W of continuous power
into a 3
load with less than 1% THD+N in speaker
mode, and 200mW of continuous average power into a
16
load with less than 1% THD+N in headphone mode.
These devices also feature thermal-overload protection.
BIAS
These devices operate from a single 5V supply, and fea-
ture an internally generated, power-supply independent,
common-mode bias voltage of 2.5V referenced to GND.
BIAS provides both click-and-pop suppression and sets
the DC bias level for the audio outputs. BIAS is internally
connected to the noninverting input of each speaker
amplifier (see the
Typical Application Circuits and
Functional Diagrams). Choose the value of the bypass
capacitor as described in the
BIAS Capacitor section.
No external load should be applied to BIAS. Any load
lowers the BIAS voltage, affecting the overall perfor-
mance of the device.
Input Multiplexer
Each amplifier features a 2:1 input multiplexer, allowing
input selection between two stereo sources. Both multi-
plexers are controlled by bit 1 in the control register
(MAX9777) or by the IN1/2 pin (MAX9778). A logic-low
selects input IN_1 and a logic-high selects input IN_2.
The input multiplexer can also be used to further
expand the number of gain options available from the
MAX9777/MAX9778 family. Connecting the audio
source to the device through two different input resis-
tors (Figure 1) increases the number of gain options
from two to four. Additionally, the input multiplexer
allows a speaker equalization network to be switched
into the speaker signal path. This is typically useful in
optimizing acoustic response from speakers with small
physical dimensions.
Headphone Sense Enable
The HPS input is enabled by HPS_EN (MAX9778) or the
HPS_D bit (MAX9777). HPS_D or HPS_EN determines
whether the device is in automatic detection mode or
fixed-mode operation (see Tables 1a and 1b).
MAX9777
MAX9778
AUDIO
INPUT
15k
30k
IN_1
IN_2
Figure 1. Using the Input Multiplexer for Gain Setting
INPUTS
HPS_D
BIT
HPS
SPKR/HP
BIT
MODE
GAIN
PATH*
0
X
BTL
A
01
X
SE
B
1
X
0
BTL
A or B
1
X
1
SE
A or B
Table 1a. MAX9777 HPS Setting
*Note:
A—GAINA path selected
B—GAINB path selected
A or B—Gain path selected by GAINAB control bit in register
02h
相关PDF资料 |
PDF描述 |
|---|---|
| D38999/20KE6SNLC | CONN HSG RCPT 6POS WALL MT SCKT |
| MS27473T24B4SCLC | CONN HSG PLUG 56POS STRGHT SCKT |
| LTC2414IGN#TR | IC ADC 8CH 24BIT DIFFINPUT28SSOP |
| MS27473T24B4SBLC | CONN HSG PLUG 56POS STRGHT SCKT |
| D38999/26JJ4PALC | CONN HSG PLUG 56POS STRGHT PINS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX9778ETI+ | 功能描述:音频放大器 Integrated Circuits (ICs) RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| MAX9778ETI+T | 功能描述:音频放大器 Integrated Circuits (ICs) RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| MAX9779ETI+ | 功能描述:音频放大器 Integrated Circuits (ICs) RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| MAX9779ETI+T | 功能描述:音频放大器 Integrated Circuits (ICs) RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| MAX977EEE | 功能描述:校验器 IC 3V/5V Dual-Speed Comparator RoHS:否 制造商:STMicroelectronics 产品: 比较器类型: 通道数量: 输出类型:Push-Pull 电源电压-最大:5.5 V 电源电压-最小:1.1 V 补偿电压（最大值）:6 mV 电源电流（最大值）:1350 nA 响应时间: 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:SC-70-5 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。