- 您现在的位置：买卖IC网 > PDF目录10925 > MAX9853ETM+ (Maxim Integrated Products)IC CODEC AUDIO STEREO 48TQFN PDF资料下载
参数资料
| 型号： | MAX9853ETM+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 29/71页 |
| 文件大小： | 0K |
| 描述： | IC CODEC AUDIO STEREO 48TQFN |
| 标准包装： | 43 |
| 类型： | 立体声音频 |
| 数据接口： | 串行 |
| 分辨率（位）： | 18 b |
| ADC / DAC 数量： | 2 / 2 |
| 三角积分调变： | 是 |
| S/N 比，标准 ADC / DAC (db)： | 81.5 / 88 |
| 动态范围，标准 ADC / DAC (db)： | 82 / 87.5 |
| 电压 - 电源，模拟： | 2.6 V ~ 3.3 V |
| 电压 - 电源，数字： | 1.7 V ~ 3.3 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 48-WFQFN 裸露焊盘 |
| 供应商设备封装： | 48-TQFN-EP（7x7） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页当前第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页
MAX9851/MAX9853
Stereo Audio CODECs with Microphone, DirectDrive
Headphones, Speaker Amplifiers, or Line Outputs
______________________________________________________________________________________
35
Internal Timing
The MAX9851/MAX9853 operate from either a 13MHz
or 26MHz master input clock (MCLK). 16kHz voice
mode requires a 26MHz clock. The quality of the clock
signal has a direct relationship with the dynamic range
performance of the data converters. Clock jitter below
100psRMS is necessary to maintain maximum perfor-
mance figures.
The MAX9851/MAX9853 make extensive use of MCLK
for all chip functions. The digital circuitry and Class D
amplifiers require a master clock to operate.
Once the MAX9851/MAX9853 are initialized, MCLK is
not required during modes where the ADC and DAC
are disabled (for instance, playing line inputs through
the headphone outputs). However, MCLK needs to be
applied for a short period of time (> 1ms) after
power-on to initialize volume control circuitry—this
is only once per power-on.
Voiceband Filters
The MAX9851/MAX9853 provide mono voiceband filter-
ing for both output and input digital audio signals on the
primary interface. Set ABPE to 1 (register 0x07, bit B5) to
enable the highpass component of the voiceband filtering
on the output of the ADC. Similarly, set DBPE to 1 (regis-
ter 0x07, bit B4) to enable the highpass component of the
voiceband filtering for incoming data on the primary digi-
tal audio interface. Voiceband filtering is available on
either interface for outgoing digital audio from the ADC,
and incoming data only on the primary S1 digital audio
interface. The voiceband filters only operate when the
MAX9851/MAX9853 are configured in voice mode. The
DAC and ADC voiceband filters are identical, with sam-
ple-rate-specific corner frequencies. Operating in 8kHz
voice mode, the filter passband extends from 130Hz to
3.5kHz. In 16kHz voice mode, the filter passband extends
from 260Hz to 7kHz. Stopband attenuation is greater
than 28dB for low frequency and 75dB for high frequen-
cies and the lowpass cutoff frequency is below fS / 2.
See the Typical Operating Characteristics for filter char-
acteristics.
Line Inputs
The MAX9851/MAX9853 provide two single-ended
audio line inputs for mixing with analog audio from
either the ADC record path or to the DAC playback
path. Each line input amplifier has a programmable-
gain function controlled by PGAL1 and PGAL2 (regis-
ters 0x0E and 0x0F). The gain is adjustable over the
+30dB to -32dB range in 2dB increments.
DirectDrive Headphone
and Receiver Amplifiers
The MAX9851/MAX9853 headphone and receiver ampli-
fiers make use of Maxim’s DirectDrive architecture to
create ground-biased outputs as shown in Figure 5.
Traditional single-supply headphone amplifiers have
their outputs biased about a nominal DC voltage, typical-
ly half the supply. Large coupling capacitors are typically
needed to block this DC bias from the headphone.
Without these capacitors, a significant amount of DC cur-
rent flows to the headphone, resulting in unnecessary
power dissipation and possible damage to both head-
phone and headphone amplifier. The DirectDrive archi-
tecture uses a charge pump to create an internal
negative supply voltage. This allows the MAX9851/
MAX9853 headphone and receiver outputs to be biased
about ground, almost doubling the dynamic range while
operating from a single supply. With no DC component,
there is no need for the large DC-blocking capacitors.
Instead of two large (33F to 330F) capacitors, the
MAX9851/MAX9853 charge pump requires only two
small ceramic capacitors (0.22F and 1F), conserving
board space, reducing cost, improving the frequency
response, and THD of the headphone amplifier. In addi-
tion to the cost and size disadvantages, the DC-blocking
capacitors required by conventional headphone ampli-
fiers limit low-frequency response and decrease PSRR
performance. Some dielectrics can significantly distort
the audio signal.
相关PDF资料 |
PDF描述 |
|---|---|
| VE-23Y-IV-F1 | CONVERTER MOD DC/DC 3.3V 99W |
| VE-23X-IX-F4 | CONVERTER MOD DC/DC 5.2V 75W |
| VE-23X-IX-F3 | CONVERTER MOD DC/DC 5.2V 75W |
| VE-23X-IX-F2 | CONVERTER MOD DC/DC 5.2V 75W |
| MAX9851ETM+ | IC CODEC AUDIO STEREO 48TQFN-EP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX9853ETM+ | 功能描述:接口—CODEC Stereo Audio CODEC w/DirectDrive Amp RoHS:否 制造商:Texas Instruments 类型: 分辨率: 转换速率:48 kSPs 接口类型:I2C ADC 数量:2 DAC 数量:4 工作电源电压:1.8 V, 2.1 V, 2.3 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:DSBGA-81 封装:Reel |
| MAX9853ETM+T | 功能描述:接口—CODEC Stereo Audio CODEC w/DirectDrive Amp RoHS:否 制造商:Texas Instruments 类型: 分辨率: 转换速率:48 kSPs 接口类型:I2C ADC 数量:2 DAC 数量:4 工作电源电压:1.8 V, 2.1 V, 2.3 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:DSBGA-81 封装:Reel |
| MAX9853EVCMODU | 功能描述:音频 IC 开发工具 Evaluation Kit/Evaluation System for the MAX9853 RoHS:否 制造商:Texas Instruments 产品:Evaluation Kits 类型:Audio Amplifiers 工具用于评估:TAS5614L 工作电源电压:12 V to 38 V |
| MAX9853EVKIT | 功能描述:音频 IC 开发工具 Evaluation Kit/Evaluation System for the MAX9853 RoHS:否 制造商:Texas Instruments 产品:Evaluation Kits 类型:Audio Amplifiers 工具用于评估:TAS5614L 工作电源电压:12 V to 38 V |
| MAX9856ATL/V+ | 功能描述:接口—CODEC Low-Power Audio Codec With Directdrive. Headphone Amplifiers RoHS:否 制造商:Texas Instruments 类型: 分辨率: 转换速率:48 kSPs 接口类型:I2C ADC 数量:2 DAC 数量:4 工作电源电压:1.8 V, 2.1 V, 2.3 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:DSBGA-81 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。