- 您现在的位置：买卖IC网 > PDF目录98009 > MAXQ7670AATL/V+ (MAXIM INTEGRATED PRODUCTS INC) RISC MICROCONTROLLER, PQCC40 PDF资料下载
参数资料
| 型号： | MAXQ7670AATL/V+ |
| 厂商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | RISC MICROCONTROLLER, PQCC40 |
| 封装： | 5 X 5 MM, ROHS COMPLIANT, TQFN-40 |
| 文件页数： | 15/38页 |
| 文件大小： | 474K |
| 代理商： | MAXQ7670AATL/V+ |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页当前第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页
MAXQ7670A
Microcontroller with 12-Bit ADC,
PGA, 64KB Flash, and CAN Interface
22
______________________________________________________________________________________
System Clock Generator
The MAXQ7670A oscillator module provides the master
clock generator that supplies the system clock for the
C core and all of the peripheral modules. The high-fre-
quency oscillator operates with an 8MHz or 16MHz
crystal. Alternatively, use the integrated RC oscillator in
applications that do not require precise timing. The
MAXQ7670A executes most instructions in a single
SYSCLK period. The oscillator module contains all of
the primary clock generation circuitry. Figure 7 shows a
block diagram of the system clock module.
The MAXQ7670A contains the following features for
generating its master clock signal timing source:
Internal, fast-starting, 15MHz RC oscillator eliminates
external crystal
Internal high-frequency oscillator that can drive an
external 8MHz or 16MHz crystal
External high-frequency 0.166MHz to 16MHz clock input
Power-up timer
Power-saving management modes
Fail-safe modes
Watchdog Timer
The primary function of the watchdog timer is to super-
vise software execution, watching for stalled or stuck
software. The watchdog timer performs a controlled
system restart when the C fails to write to the watch-
dog timer register before a selectable timeout interval
expires. A watchdog timer typically has four objectives:
1) To detect if a system is operating normally
2) To detect an infinite loop in any of the tasks
3) To detect an arbitration deadlock involving two or
more tasks
4) To detect if some lower priority tasks are not getting
to run because of higher priority tasks
As illustrated in Figure 8, the internal RC oscillator
(CLK_RC) drives the watchdog timer through a series
of dividers. The programmable divider output deter-
mines the timeout interval. When enabled, the interrupt
flag WDIF sets. A system reset occurs after a time
delay (based on the divider ratio) unless an interrupt
service routine clears the watchdog interrupt.
The watchdog timer functions as the source of both the
watchdog interrupt and the watchdog reset. The inter-
rupt timeout has a default divide ratio of 212 of the
CLK_RC, with the watchdog reset set to timeout 29
clock cycles later. With the nominal RC oscillator value
of 15MHz, an interrupt timeout occurs every 0.273ms,
followed by a watchdog reset 34s later. The watchdog
timer resets to the default divide ratio following any
reset event. Use the WD0 and WD1 bits in the WDCN
register to increase the watchdog interrupt period.
Changing the WD[1:0] bits before a watchdog interrupt
timeout occurs (i.e. before the watchdog reset counter
begins) resets the watchdog timer count. The watch-
dog reset timeout occurs 512 RC oscillator cycles after
the watchdog interrupt timeout. For more information on
the MAXQ7670A watchdog timer, refer to the
MAXQ7670 User’s Guide.
CD1
CD0
PMME
SYSCLK
MUX
CLK_RC
CLOCK
DIVIDE
HF
XTAL
OSC
RC
OSC
XIN
XOUT
XT
EXTHF
RCE
HFE
Figure 7. High-Frequency and RC Oscillator Functional
Diagram
EWDI
WD0
RWT
WD1
CLK_RC
(15MHz)
INTERRUPT
WTRF
RESET
WDIF
TIMEOUT
TIME
212
DIV 212
DIV 23
215 218 221
EWT
RESET
Figure 8. Watchdog Functional Diagram
相关PDF资料 |
PDF描述 |
|---|---|
| MAXQ8913EWG+T | 16-BIT, FLASH, 10 MHz, RISC MICROCONTROLLER, PBGA58 |
| MB86290APFVS | GRAPHICS PROCESSOR, PQFP240 |
| MB86295S-PB-GS | GRAPHICS PROCESSOR, PBGA256 |
| MB86603 | SCSI BUS CONTROLLER, PQFP176 |
| MB86604A-PF | SCSI BUS CONTROLLER, PQFP100 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAXQ7670ATL/V+ | 功能描述:16位微控制器 - MCU MCU w/12-Bit ADC PGA 64KB Flash & CAN Int RoHS:否 制造商:Texas Instruments 核心:RISC 处理器系列:MSP430FR572x 数据总线宽度:16 bit 最大时钟频率:24 MHz 程序存储器大小:8 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:VQFN-40 安装风格:SMD/SMT |
| MAXQ7670ATL/V+T | 功能描述:16位微控制器 - MCU MCU w/12-Bit ADC PGA 64KB Flash & CAN Int RoHS:否 制造商:Texas Instruments 核心:RISC 处理器系列:MSP430FR572x 数据总线宽度:16 bit 最大时钟频率:24 MHz 程序存储器大小:8 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:VQFN-40 安装风格:SMD/SMT |
| MAXQ7670ATL+ | 功能描述:16位微控制器 - MCU MCU w/12-Bit ADC PGA 64KB Flash & CAN Int RoHS:否 制造商:Texas Instruments 核心:RISC 处理器系列:MSP430FR572x 数据总线宽度:16 bit 最大时钟频率:24 MHz 程序存储器大小:8 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:VQFN-40 安装风格:SMD/SMT |
| MAXQ7670ATL+T | 功能描述:16位微控制器 - MCU MCU w/12-Bit ADC PGA 64KB Flash & CAN Int RoHS:否 制造商:Texas Instruments 核心:RISC 处理器系列:MSP430FR572x 数据总线宽度:16 bit 最大时钟频率:24 MHz 程序存储器大小:8 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:VQFN-40 安装风格:SMD/SMT |
| MAXQ7670EVKIT+ | 功能描述:开发板和工具包 - 其他处理器 MAXQ7670 Eval Kit RoHS:否 制造商:Freescale Semiconductor 产品:Development Systems 工具用于评估:P3041 核心:e500mc 接口类型:I2C, SPI, USB 工作电源电压: |
发布紧急采购，3分钟左右您将得到回复。