- 您现在的位置：买卖IC网 > PDF目录98010 > MB90822PFV (FUJITSU LTD) 16-BIT, MROM, 24 MHz, MICROCONTROLLER, PQFP80 PDF资料下载
参数资料
| 型号： | MB90822PFV |
| 厂商： | FUJITSU LTD |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 16-BIT, MROM, 24 MHz, MICROCONTROLLER, PQFP80 |
| 封装： | 0.50 MM PITCH, PLASTIC, LQFP-80 |
| 文件页数： | 8/100页 |
| 文件大小： | 1414K |
| 代理商： | MB90822PFV |
第1页第2页第3页第4页第5页第6页第7页当前第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页
MB90820 Series
15
■ HANDLING DEVICES
Special care is required for the following when handling the device :
Preventing latch-up
Stabilization of supply voltage
Treatment of unused pins
Using external clock
Power supply pins (VCC /VSS )
Pull-up/pull-down resistors
Crystal Oscillator Circuit
Turning-on Sequence of Power Supply to A/D Converter and D/A Converter, and Analog Inputs
Connection of Unused Pins of A/D Converter and D/A Converter if A/D Converter and D/A Converter are unused
Notes on energization
Notes on During Operation of PLL Clock Mode
1.
Preventing latch-up
CMOS IC chips may suffer latch-up under the following conditions :
A voltage higher than VCC or lower than VSS is applied to an input or output pin.
A voltage higher than the rated voltage is applied between VCC and VSS.
The AVCC power supply is applied before the VCC voltage.
Latch-up may increase the power supply current drastically, causing thermal damage to the device.
In using the devices, take sufficient care to avoid exceeding maximum ratings.
For the same reason, also be careful not to let the analog power-supply voltage (AVCC, AVR) exceed the digital
power-supply voltage.
2.
Stabilization of supply voltage
A sudden change in the supply voltage may cause the device to malfunction even within the specified VCC supply
voltage operation range. Therefore, the VCC supply voltage should be stabilized.
For reference, the supply voltage should be controlled so that VCC ripple variations (peak-to-peak values) at
commercial frequencies (50 Hz to 60 Hz) fall below 10
% of the standard VCC supply voltage and the coefficient
of fluctuation does not exceed 0.1 V/ms at instantaneous power switching.
3.
Treatment of unused pins
Leaving unused input pins open may result in misbehavior or latch up and possible permanent damage of the
device. Therefore they must be pulled up or pulled down through resistors. In this case those resistors should
be more than 2 k
.
Unused bidirectional pins should be set to the output state and can be left open, or the input state with the above
described connection.
4.
Using external clock
To use external clock, drive the X0 pin and leave X1 pin open.
X0
X1
MB90820 series
Open
相关PDF资料 |
PDF描述 |
|---|---|
| MB90911ASPMC | 16-BIT, FLASH, 32 MHz, MICROCONTROLLER, PQFP48 |
| MB90F912BSPMC | 16-BIT, FLASH, 32 MHz, MICROCONTROLLER, PQFP48 |
| MB90F243PFV-ES-BND | 16-BIT, FLASH, 32 MHz, MICROCONTROLLER, PQFP80 |
| MB90F372PMT-G | 16-BIT, FLASH, 16 MHz, MICROCONTROLLER, PQFP144 |
| MB90F498GPFM | 16-BIT, FLASH, 16 MHz, MICROCONTROLLER, PQFP64 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MB90823 | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:16-bit Proprietary Microcontroller |
| MB90823B | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:16-bit Microcontroller |
| MB90823BPF | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:16-bit Microcontroller |
| MB90823BPMC | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:16-bit Microcontroller |
| MB90823BPMC1 | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:16-bit Microcontroller |
发布紧急采购，3分钟左右您将得到回复。