- 您现在的位置：买卖IC网 > PDF目录80409 > MB90F803SPF-G (FUJITSU LTD) 16-BIT, FLASH, 25 MHz, MICROCONTROLLER, PQFP100 PDF资料下载
参数资料
| 型号： | MB90F803SPF-G |
| 厂商： | FUJITSU LTD |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 16-BIT, FLASH, 25 MHz, MICROCONTROLLER, PQFP100 |
| 封装： | 20 X 14 MM, 3.35 MM HEIGHT, 0.65 MM PITCH, PLASTIC, QFP-100 |
| 文件页数： | 6/92页 |
| 文件大小： | 2178K |
| 代理商： | MB90F803SPF-G |
第1页第2页第3页第4页第5页当前第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页
MB90800 Series
14
DS07-13733-6E
■ HANDLING DEVICES
1.
Preventing Latch-up, Turning on Power Supply
Latch-up may occur on CMOS IC under the following conditions:
If a voltage higher than VCC or lower than VSS is applied to input and output pins,
A voltage higher than the rated voltage is applied between VCC pin and VSS pin.
If the AVCC power supply is turned on before the VCC voltage.
Ensure that you apply a voltage to the analog power supply at the same time as VCC or after you turn on the
digital power supply (when you perform power-off, turn off the analog power supply first or at the same time as
VCC and the digital power supply).
When latch-up occurs, power supply current increases rapidly and might thermally damage elements. When
using CMOS IC, take great care to prevent the occurrence of latch-up.
2.
Treatment of unused pins
If unused input pins are left open, they may cause abnormal operation or latch-up which may lead to permanent
damage to the semiconductor. Any such pins should be pulled up or pulled down through resistance of at least
2 k
Ω.
Any unused input/output pins should be left open in output status, or if found set to input status, they should be
treated in the same way as input pins.
Any unused output pins should be left open.
3.
Treatment of A/D converter power supply pins
Even if the A/D converter is not used, pins should be connected so that AVCC
= VCC, and AVSS = VSS.
4.
About the attention when the external clock is used
In using an external clock, drive pin X0 only and leave pin X1 open.
The example of using an external clock is shown below.
Please set X0A
= GND and X1A = open without subclock mode.
The following figure shows the using sample.
X0
X1
OPEN
MB90800 Series
X0A
X1A
OPEN
MB90800 Series
相关PDF资料 |
PDF描述 |
|---|---|
| MPC8543EVTANGA | 32-BIT, 800 MHz, MICROPROCESSOR, PBGA783 |
| MPC8545VUATG | 32-BIT, 1200 MHz, MICROPROCESSOR, CBGA783 |
| MPC8548HXAQGA | 32-BIT, 1000 MHz, MICROPROCESSOR, CBGA783 |
| MC312XDP512F0VFVR | 16-BIT, FLASH, 40 MHz, MICROCONTROLLER, PQFP144 |
| MSC8122TMP6400 | 32-BIT, 400 MHz, OTHER DSP, PBGA431 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MB90F804-201PFR-GE1 | 制造商:FUJITSU 功能描述: |
| MB90F867APFR-G-SNE1 | 制造商:FUJITSU 功能描述: |
| MB90F867ASPF-GE1 | 制造商:FUJITSU 功能描述:IC 16BIT MCU I2C SMD QFP100 |
| MB90F867ASPFR-GE1 | 制造商:FUJITSU 功能描述: |
| MB90F867ASPFR-G-SPE1 | 制造商:FUJITSU 功能描述: |
发布紧急采购，3分钟左右您将得到回复。