- 您现在的位置：买卖IC网 > PDF目录80409 > MB90F803SPF-G (FUJITSU LTD) 16-BIT, FLASH, 25 MHz, MICROCONTROLLER, PQFP100 PDF资料下载
参数资料
| 型号： | MB90F803SPF-G |
| 厂商： | FUJITSU LTD |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 16-BIT, FLASH, 25 MHz, MICROCONTROLLER, PQFP100 |
| 封装： | 20 X 14 MM, 3.35 MM HEIGHT, 0.65 MM PITCH, PLASTIC, QFP-100 |
| 文件页数： | 7/92页 |
| 文件大小： | 2178K |
| 代理商： | MB90F803SPF-G |
第1页第2页第3页第4页第5页第6页当前第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页
MB90800 Series
DS07-13733-6E
15
5.
Treatment of power supply pins (VCC/VSS)
In products with multiple VCC or VSS pins, the pins of the same potential are internally connected in the device
to avoid abnormal operations including latch-up. However, you must connect all power supply pins to external
power supply and a ground line to lower the electro-magnetic emission level, to prevent abnormal operation of
strobe signals caused by the rise in the ground level, and to conform to the total output current rating.
Moreover, connect the current supply source with the VCC and VSS pins of this device at the low impedance.
It is also advisable to connect a ceramic capacitor of approximately 0.1
μF as a bypass capacitor between VCC
and VSS near this device.
6.
About Crystal oscillators circuit
Noise near the X0/X1 pins and X0A/X1A pins may cause the device to malfunction. Design the printed circuit
board so that X0/X1 pins and X0A/X1A pins, the crystal oscillator (or the ceramic oscillator) and the bypass
capacitor to ground are located as close to the device as possible.
It is strongly recommended to design the PC board artwork with the X0/X1 pins and X0A/X1A pins surrounded
by ground plane because stable operation can be expected with such a layout.
Please ask the crystal maker to evaluate the oscillational characteristics of the crystal and this device.
7.
Caution on Operations during PLL Clock Mode
On this microcontroller, if in case the crystal oscillator breaks off or an external reference clock input stops while
the PLL clock mode is selected, a self-oscillator circuit contained in the PLL may continue its operation at its
self-running frequency. However, Fujitsu will not guarantee results of operations if such failure occurs.
8.
Stabilization of Supply Power Supply
A sudden change in the supply voltage may cause the device to malfunction even within the VCC supply voltage
operating range.Therefore, the VCC supply voltage should be stabilized. For reference, the supply voltage should
be controlled so that VCC ripple variations (peak- to-peak values) at commercial frequencies (50 Hz/60 Hz) fall
below 10
% of the standard VCC supply voltage and the coefficient of fluctuation does not exceed 0.1 V/ms at
instantaneous power switching.
9.
Note on Using the two-subsystem product as one-subsystem product
If you are using only one subsystem of the MB90800 series that come in one two-subsystem product, use it with
X0A
= VSS and X1A = OPEN.
10. Write to FLASH
Ensure that you must write to FLASH at the operating voltage VCC
= 3.0 V to 3.6 V.
相关PDF资料 |
PDF描述 |
|---|---|
| MPC8543EVTANGA | 32-BIT, 800 MHz, MICROPROCESSOR, PBGA783 |
| MPC8545VUATG | 32-BIT, 1200 MHz, MICROPROCESSOR, CBGA783 |
| MPC8548HXAQGA | 32-BIT, 1000 MHz, MICROPROCESSOR, CBGA783 |
| MC312XDP512F0VFVR | 16-BIT, FLASH, 40 MHz, MICROCONTROLLER, PQFP144 |
| MSC8122TMP6400 | 32-BIT, 400 MHz, OTHER DSP, PBGA431 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MB90F804-201PFR-GE1 | 制造商:FUJITSU 功能描述: |
| MB90F867APFR-G-SNE1 | 制造商:FUJITSU 功能描述: |
| MB90F867ASPF-GE1 | 制造商:FUJITSU 功能描述:IC 16BIT MCU I2C SMD QFP100 |
| MB90F867ASPFR-GE1 | 制造商:FUJITSU 功能描述: |
| MB90F867ASPFR-G-SPE1 | 制造商:FUJITSU 功能描述: |
发布紧急采购，3分钟左右您将得到回复。