- 您现在的位置：买卖IC网 > PDF目录80534 > MB91F346BPFT-GE1 32-BIT, FLASH, 50 MHz, RISC MICROCONTROLLER, PQFP100 PDF资料下载
参数资料
| 型号： | MB91F346BPFT-GE1 |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 32-BIT, FLASH, 50 MHz, RISC MICROCONTROLLER, PQFP100 |
| 封装： | 12 X 12 MM, 1.20 MM HEIGHT, 0.40 MM PITCH, PLASTIC, TQFP-100 |
| 文件页数： | 9/72页 |
| 文件大小： | 657K |
| 代理商： | MB91F346BPFT-GE1 |
第1页第2页第3页第4页第5页第6页第7页第8页当前第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页
MB91345 Series
17
■ HANDLING DEVICES
Preventing Latch-up
Latch-up may occur in a COMS IC if a voltage greater than VCC pin, or less than VSS pin is applied to input
and output pins, or if an above-rating voltage is applied between VCC pin and VSS pin. If the latch-up occurs,
the significantly increases the power supply current and may cause thermal destruction of an element. Thus,
When you use a CMOS IC, be very careful not to exceed maximum voltage rating.
Treatment of Unused input pins
Do not leave an unused input pin open, since it may cause a malfunction. Thus, use pull-up or pull-down resistor.
About power supply pins
If there are multiple VCC pin or VSS pin, from the point of view of device design, pins to be of the same level
are connected the inside of the device to prevent such malfunctioning as latch-up. Be sure to connect all of them
to the power supply and ground externally for reducing unnecessary radiation, prevent malfunctioning of the
strobe signal due to the rise of ground level, and observe the total output current standard. In addition, consid-
eration should be given to connecting VCC/VSS of this device with as low an impedance as possible from the
current supply source. Also, we recommend connecting a ceramic capacitor of about 0.1 F as a bypass capacitor
between VCC and VSS near this device.
About crystal oscillator circuit
Noise near the X0 and X1 pins can cause this device to malfunction. Design the PC board such that X0 and X1
pins, crystal oscillator (or ceramic oscillator) , and bypass capacitor to the ground are placed as near one another
as possible. It is strongly recommended to design the PC board artwork with the X0/X1 pins surrounded by a
ground plane, as it expects stable operations.
Please ask the crystal maker to evaluate the oscillational characteristics of the crystal and this device.
About mode pins (MD0 to MD2)
These pins should be connected directly to VCC or VSS pins. To prevent the device erroneously switching to
test mode due to noise, design the PC board such that the distance between the mode pins and VCC or VSS
pins is as short as possible and the connection impedance is low.
About operation at power-on
Be sure to set initialized reset (INIT) with INIT pin immediately after power-on.
Immediately after turning on the power, be sure to continue connecting the Low level input to the INIT pin for
the stabilization wait time required for oscillator circuit, to secure the stabilization wait time of the oscillator and
regulator (For INIT via the INIT pin, the oscillation stabilization wait time setting is initialized to the minimum value) .
About oscillation input at power on
When turning on the power, be sure that clock input is maintained until the device is released from the oscillation
stabilization wait state.
Note on power-on/off sequences
When turning on the power, the output pin may be indeterminate until the internal power supply stabilizes.
相关PDF资料 |
PDF描述 |
|---|---|
| MSM80C31F-1GS-VIK | 8-BIT, 16 MHz, MICROCONTROLLER, PQFP44 |
| MAQ281CB | 16-BIT, MICROPROCESSOR, DMA64 |
| MAR281CC | 16-BIT, MICROPROCESSOR, DMA64 |
| MD80C51UFXXX-25 | 8-BIT, MROM, 25 MHz, MICROCONTROLLER, CDIP40 |
| MD80C51UXXX-25 | 8-BIT, MROM, 25 MHz, MICROCONTROLLER, CDIP40 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MB91F353A | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:32-bit Microcontroller |
| MB91F353APMCR-GE1 | 制造商:FUJITSU 功能描述: |
| MB91F353APMCR-G-JNE1 | 制造商:FUJITSU 功能描述: |
| MB91F353APMT | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:32-bit Microcontroller |
| MB91F353APMT-GE1 | 制造商:FUJITSU 功能描述:IC 16BIT MCU 5V SMD LQFP120 |
发布紧急采购，3分钟左右您将得到回复。