- 您现在的位置：买卖IC网 > PDF目录80519 > MB95F478HPMC2-G-SNE2 (FUJITSU LTD) MICROCONTROLLER, PQFP64 PDF资料下载
参数资料
| 型号： | MB95F478HPMC2-G-SNE2 |
| 厂商： | FUJITSU LTD |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | MICROCONTROLLER, PQFP64 |
| 封装： | 12 X 12 MM, 1.70 MM HEIGHT, 0.65 MM PITCH, PLASTIC, LQFP-64 |
| 文件页数： | 41/76页 |
| 文件大小： | 3707K |
| 代理商： | MB95F478HPMC2-G-SNE2 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页当前第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页
MB95410H/470H Series
46
DS702-00004-0v01-E
(Continued)
*3: Applicable to the following pins: P00 to P07, P10, P11, P13 to P16, P20 to P22, P40 to P43, P50 to P53,
P60 to P67, P90 to P94, PA0 to PA7, PB0 to PB4, PC0 to PC7, PE0 to PE7, PG1, PG2, PF0 and PF1 (P40
to P43, P50 to P53, P94, PB2 to PB4 and PC4 to PC7 are only available on the MB95410H Series.)
Use under recommended operating conditions.
Use with DC voltage (current).
The HV (High Voltage) signal is an input signal exceeding the VCC voltage. Always connect a limiting resistor
between the HV (High Voltage) signal and the microcontroller before applying the HV (High Voltage) signal.
The value of the limiting resistance should be set so that when the HV (High Voltage) signal is applied the
input current to the microcontroller pin does not exceed rated values, either instantaneously or for prolonged
periods.
When the microcontroller drive current is low, such as in low power consumption modes, the HV (High
Voltage) input potential may pass through the protective diode to increase the potential of the VCC pin, and
thus affects other devices.
If the HV (High Voltage) signal is input when the microcontroller power supply is off (not fixed at 0 V), since
power is supplied from the pins, incomplete operations may be executed.
If the HV (High Voltage) input is input after power-on, since power is supplied from the pins, the voltage
of power supply may not be sufficient to enable a power-on reset.
Do not leave the HV (High Voltage) input pin unconnected.
Example of a recommended circuit
WARNING: Semiconductor devices can be permanently damaged by application of stress (voltage, current,
temperature, etc.) in excess of absolute maximum ratings. Do not exceed these ratings.
HV(High Voltage) input (0 V to 16 V)
Protective diode
VCC
N-ch
P-ch
R
Limiting
resistor
Input/Output equivalent circuit
相关PDF资料 |
PDF描述 |
|---|---|
| MC9S08SG16E1MTJR | MICROCONTROLLER, PDSO16 |
| MK2745-20STR | 108 MHz, VIDEO CLOCK GENERATOR, PDSO16 |
| MK2751-01STR | 66 MHz, VIDEO CLOCK GENERATOR, PDSO16 |
| M37272EFSP | 8-BIT, OTPROM, 8 MHz, MICROCONTROLLER, PDIP42 |
| M37902FECHP | 16-BIT, FLASH, MICROCONTROLLER, PQFP100 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MB95F478KPMC1-ES-SNE2 | 制造商:FUJITSU 功能描述:8-bit FX series microcontroller |
| MB95F478KPMC2-G-SNE2 | 制造商:FUJITSU 功能描述:8-bit MCUs |
| MB95F563HWQN-G-JNERE1 | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:8-bit Microcontrollers |
| MB95F564KPF-G-JNE2 | 功能描述:IC MCU 8BIT 20KB FLASH 20TSSOP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:8FX MB95560H 标准包装:60 系列:PSOC® 3 CY8C38xx 核心处理器:8051 芯体尺寸:8-位 速度:67MHz 连通性:EBI/EMI，I²C，LIN，SPI，UART/USART 外围设备:电容感应，DMA，LCD，POR，PWM，WDT 输入/输出数:25 程序存储器容量:64KB（64K x 8） 程序存储器类型:闪存 EEPROM 大小:2K x 8 RAM 容量:8K x 8 电压 - 电源 (Vcc/Vdd):1.71 V ~ 5.5 V 数据转换器:A/D 2x20b，D/A 4x8b 振荡器型:内部 工作温度:-40°C ~ 85°C 封装/外壳:48-VFQFN 裸露焊盘 包装:托盘 |
| MB95F636HP-ES-SH-SNE2 | 制造商:FUJITSU 功能描述:8-bit MCU |
发布紧急采购，3分钟左右您将得到回复。