- 您现在的位置：买卖IC网 > PDF目录299463 > MBM29DL161BE-90PBT (FUJITSU LTD) 1M X 16 FLASH 3V PROM, 90 ns, PBGA48 PDF资料下载
参数资料
| 型号： | MBM29DL161BE-90PBT |
| 厂商： | FUJITSU LTD |
| 元件分类： | PROM |
| 英文描述： | 1M X 16 FLASH 3V PROM, 90 ns, PBGA48 |
| 封装： | PLASTIC, FBGA-48 |
| 文件页数： | 33/76页 |
| 文件大小： | 1145K |
| 代理商： | MBM29DL161BE-90PBT |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页当前第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页
MBM29DL16XTE/BE70/90
39
driving status information on DQ7 at one instant of time and then that byte’s valid data at the next instant of time.
Depending on when the system samples the DQ7 output, it may read the status or valid data. Even if the device
has completed the Embedded Algorithm operation and DQ7 has a valid data, the data outputs on DQ6 to DQ0
may be still invalid. The valid data on DQ7 to DQ0 will be read on the successive read attempts.
The Data Polling feature is only active during the Embedded Programming Algorithm, Embedded Erase Algorithm
or sector erase time-out. (See “Hardware Sequence Flags Table”.)
See “(6) AC Waveforms for Data Polling during Embedded Algorithm Operations” in sTIMING DIAGRAM for the
Data Polling timing specifications and diagrams.
DQ6
Toggle Bit I
The MBM29DL16XTE/BE also feature the “Toggle Bit I” as a method to indicate to the host system that the
Embedded Algorithms are in progress or completed.
During an Embedded Program or Erase Algorithm cycle, successive attempts to read (CE or OE toggling) data
from the devices will result in DQ6 toggling between “1” and “0”. Once the Embedded Program or Erase Algorithm
cycle is completed, DQ6 will stop toggling and valid data will be read on the next successive attempts. During
programming, the Toggle Bit I is valid after the rising edge of the fourth write pulse in the four write pulse sequence.
For chip erase and sector erase, the Toggle Bit I is valid after the rising edge of the sixth write pulse in the six
write pulse sequence. The Toggle Bit I is active during the sector time out.
In programming, if the sector being written to is protected, the toggle bit will toggle for about 1
s and then stop
toggling without the data having changed. In erase, the devices will erase all the selected sectors except for the
ones that are protected. If all selected sectors are protected, the chip will toggle the toggle bit for about 400 s
and then drop back into read mode, having changed none of the data.
Either CE or OE toggling will cause the DQ6 to toggle. In addition, an Erase Suspend/Resume command will
cause the DQ6 to toggle.
The system can use DQ6 to determine whether a sector is actively erasing or is erase-suspended. When a bank
is actively erasing (that is, the Embedded Erase Algorithm is in progress), DQ6 toggles. When a bank enters the
Erase Suspend mode, DQ6 stops toggling. Successive read cycles during the erase-suspend-program cause
DQ6 to toggle.
To operate toggle bit function properly, CE or OE must be high when bank address is changed.
See “(7) AC Waveforms for Toggle Bit I during Embedded Algorithm Operations” in sTIMING DIAGRAM for the
Toggle Bit I timing specifications and diagrams.
DQ5
Exceeded Timing Limits
DQ5 will indicate if the program or erase time has exceeded the specified limits (internal pulse count). Under
these conditions DQ5 will produce a “1”. This is a failure condition which indicates that the program or erase
cycle was not successfully completed. Data Polling is the only operating function of the devices under this
condition. The CE circuit will partially power down the device under these conditions (to approximately 2 mA).
The OE and WE pins will control the output disable functions as described in “MBM29DL16XTE/BE User Bus
Operations Tables (BYTE = VIH and BYTE = VIL)” in sDEVICE BUS OPERATION.
The DQ5 failure condition may also appear if a user tries to program a non blank location without erasing. In this
case the devices lock out and never complete the Embedded Algorithm operation. Hence, the system never
reads a valid data on DQ7 bit and DQ6 never stops toggling. Once the devices have exceeded timing limits, the
相关PDF资料 |
PDF描述 |
|---|---|
| MBM29DL163TD12PBT | 1M X 16 FLASH 3V PROM, 120 ns, PBGA48 |
| MBM29DL32TF70TN | 2M X 16 FLASH 3V PROM, 70 ns, PDSO48 |
| MBM29F800TA-70PFTN-E1 | 512K X 16 FLASH 5V PROM, 70 ns, PDSO48 |
| MBR-2051-1B5T | 51 CONTACT(S), MALE, D MICROMINIATURE CONNECTOR, SOLDER, PLUG |
| MBR-2069-0A1T | 69 CONTACT(S), MALE, D MICROMINIATURE CONNECTOR, SOLDER, PLUG |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MBM29DL161BE-90TN | 制造商:SPANSION 制造商全称:SPANSION 功能描述:FLASH MEMORY CMOS 16M (2M X 8/1M X 16) BIT Dual Operation |
| MBM29DL161BE-90TR | 制造商:SPANSION 制造商全称:SPANSION 功能描述:FLASH MEMORY CMOS 16M (2M X 8/1M X 16) BIT Dual Operation |
| MBM29DL161TD | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:16M (2M x 8/1M x 16) BIT Dual Operation |
| MBM29DL161TD-70PBT | 制造商:SPANSION 制造商全称:SPANSION 功能描述:FLASH MEMORY CMOS 16M (2M X 8/1M X 16) BIT Dual Operation |
| MBM29DL161TD-70PFTN | 制造商:SPANSION 制造商全称:SPANSION 功能描述:FLASH MEMORY CMOS 16M (2M X 8/1M X 16) BIT Dual Operation |
发布紧急采购，3分钟左右您将得到回复。