- 您现在的位置：买卖IC网 > PDF目录20762 > MC10SX1130DR2G (ON Semiconductor)IC LED DRIVER LINEAR 16-SOIC PDF资料下载
参数资料
| 型号： | MC10SX1130DR2G |
| 厂商： | ON Semiconductor |
| 文件页数： | 2/9页 |
| 文件大小： | 0K |
| 描述： | IC LED DRIVER LINEAR 16-SOIC |
| 标准包装： | 2,500 |
| 输出数： | 1 |
| 内部驱动器： | 是 |
| 类型 - 主要： | 通用 |
| 频率： | 300MHz |
| 电源电压： | +5V，-5.2V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 16-SOIC |
| 包装： | 带卷 (TR) |
| 工作温度： | -40°C ~ 85°C |
MC10SX1130
V EE Stretch V EE
16 15 14
I OUT RSET I OUT
13 12 11
V CC
10
V EE
9
ECL
BUFFER
Stretch
I OUT
I OUT
D IN
D IN
PULSE WIDTH
ADJUST CIRCUIT
1
2
3
4
5
6
7
8
V BB
BIAS
CONTROL
V EE
V CC
V BB
D IN
D IN RTCO 1 RTCO 2 V EE
RTCO 1
RTCO 2
RSET
Figure 1. Pinout: SOIC ? 16
(Top View)
Table 1. PIN FUNCTION TABLE
Figure 2. Block Diagram
Pin
D IN
I OUT
STRETCH
RSET
RTCO 1 , RTCO 2
V CC
V EE
V BB
Function
Differential data inputs.
Differential open collector outputs.
Control input to select the amount of duty cycle pre-distortion. When the pin is left open, no pre-distortion is
introduced. If the pin is connected to V CC , the output LOW state current pulse width is increased by 155 ps. When it
is connected to V EE , the current pulse width is increased by 310 ps.
Resistor to set LED drive current. This resistor sets the tail current of the output current switch and should be con-
nected to the V EE plane. Since the RSET voltage compensation circuit is referenced to V EE , the RSET voltage will
track 1:1 with V EE changes, thus the voltage across the RSET resistor will remain constant.
Terminals for positive temperature tracking resistor. This resistor controls the temperature tracking rate of the voltage
at the RSET pin, which in turn sets the LED drive current tracking. If the two pins are shorted together, the nominal
tracking rate is 1.4mV/ ° C and when a 2 k W resistor is connected across the pins, the nominal tracking rate is
4.9 mV/ ° C.
Most positive power supply input. +5 V for PECL operation or ground for standard ECL operation.
Most negative power supply input. Ground for PECL operation or ? 5.2 V for standard ECL operation.
Reference voltage for use in single ended applications or when the input signal is AC coupled into the device.
http://onsemi.com
2
相关PDF资料 |
PDF描述 |
|---|---|
| RBC07DRYH | CONN EDGECARD 14POS DIP .100 SLD |
| ACE50DHRD | CONN CARD EXTEND 100POS 1MM SLD |
| RBC06DCMS | CONN EDGECARD 12POS .100 WW |
| GEC15DRYS | CONN EDGECARD 30POS DIP .100 SLD |
| ACB35DHAN | CONN EDGECARD 70POS R/A .050 DIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MC10SX1189D | 功能描述:缓冲器和线路驱动器 Fiber Channel Coax RoHS:否 制造商:Micrel 输入线路数量:1 输出线路数量:2 极性:Non-Inverting 电源电压-最大:+/- 5.5 V 电源电压-最小:+/- 2.37 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Reel |
| MC10SX1189DG | 功能描述:缓冲器和线路驱动器 Fiber Channel Coax Calbe Driver RoHS:否 制造商:Micrel 输入线路数量:1 输出线路数量:2 极性:Non-Inverting 电源电压-最大:+/- 5.5 V 电源电压-最小:+/- 2.37 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Reel |
| MC10SX1189DR2 | 功能描述:缓冲器和线路驱动器 Fiber Channel Coax RoHS:否 制造商:Micrel 输入线路数量:1 输出线路数量:2 极性:Non-Inverting 电源电压-最大:+/- 5.5 V 电源电压-最小:+/- 2.37 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Reel |
| MC10SX1189DR2G | 功能描述:缓冲器和线路驱动器 Fiber Channel Coax Calbe Driver RoHS:否 制造商:Micrel 输入线路数量:1 输出线路数量:2 极性:Non-Inverting 电源电压-最大:+/- 5.5 V 电源电压-最小:+/- 2.37 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Reel |
| MC10SX1190DT | 功能描述:缓冲器和线路驱动器 Fiber Channel Coax RoHS:否 制造商:Micrel 输入线路数量:1 输出线路数量:2 极性:Non-Inverting 电源电压-最大:+/- 5.5 V 电源电压-最小:+/- 2.37 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。