- 您现在的位置：买卖IC网 > PDF目录359132 > MC33486 (飞思卡尔半导体(中国)有限公司) Dual High Side Switch for H-Bridge Automotive Applications(适合于H桥自动应用的双高端开关) PDF资料下载
参数资料
| 型号： | MC33486 |
| 厂商： | 飞思卡尔半导体(中国)有限公司 |
| 英文描述： | Dual High Side Switch for H-Bridge Automotive Applications(适合于H桥自动应用的双高端开关) |
| 中文描述： | 双通道高边开关的H -桥汽车应用（适合于?桥自动应用的双高端开关） |
| 文件页数： | 7/9页 |
| 文件大小： | 392K |
| 代理商： | MC33486 |
MC33486
DEVICE DESCRIPTION
Dual High Side Switch for H-Bridge Automotive Applications
7
Overtemperature Protection
The DHSB incorporates over-temperature protection. Over-
temperature detection occurs when an internal high side is in
the on state. When an over-temperature condition occurs,
both outputs are affected. Both outputs are turned off to
protect the DHSB from damage (Low sides ON). The
overtemperature protection circuitry incorporates hysteresis.
Overtemperature fault condition is reported on the status
output.
High side overcurrent protection
This device incorporates a current shutdown threshold of
35A typical. When this limit is reached due to an overload
condition or a short to ground, the faulty output is tri-stated. To
clear the fault the input (Inx) line needs to return low then on
the next high transition the output will be enabled.
This information is reported on the status output.
Low side block
The low side block has control circuitry for two external N-
Channel power MOSFET
’
s. The low side control circuitry is
PWM capable and protects the Low side MOSFETS in case of
overcurrent (short to Vbat). This information is reported on the
status output.
The low side Gate controls are clamped at14V maximum
to protect the gates of the Low Sides.
During normal operation, the outputs OUT1 and OUT2 are
driven by the high side. The low side Gate driver
’
s will only
turn on when the Drain voltage (same connection as OUT1 or
2) of the internal high sides is less than 2V, which prevent any
cross-conduction in the bridge.
Low Side Overcurrent Protection
Unlike the high side overcurrent circuitry, this overcurrent
protection does not measure the current , but measures the
effect of current on the low side through a condition : Vgs >
4.3V and Vds >2V. When this set of conditions occur for at
least 8us (blanking time), both outputs OUT1 and OUT2 are
tri-stated. The full bridge is tri-stated to prevent the motor for
running in case of short to Vbat.
As Vgs and Vds are measured in respect to the DHSB
’
s
ground pin, it is essential that the low side source are
connected to this same ground, in order to prevent false
overcurrent detection due to ground shifts.
Package
The high side block is assembled into a power surface
mount package. This package offers high thermal
performances, and high current capabilities. It offers 10 pins
on each package sides, and one additional connection which
is the package heat sink (called pin 21). The heat sink acts as
the device power Vbat connection.
Soldering Information
This device is packaged in a Surface Mount Power
package indended to be soldered directly on the Printed
Circuit Board.
This device was qualified according to JEDEC standards
JESD22-A113-B and J-STD-020A with the reflow conditions
applicable for packages with thickness above 2.5mm :
Convection 220
°
C +5/-0
°
C
VPR 215-219
°
C
IR / Convection 220
°
C +5/-0
°
C
The maximum peak temperature during the soldering process
should not exceed 220
°
C (+5
°
C/-0
°
C). The time at maximum
temperature should range from 10 to 40s max.
Thermal Management
The junction to case thermal resistance is 2
°
C/W
maximum. The junction to ambient thermal resistance is
dependant on the mounting technology, and if an additional
heat sink is used. One of the most commonly used mounting
technique consists of using the printed circuit board and the
copper lines as heat sink.
Figure 2 is an example of printed circuit board layout. It
has a total of 10cm
2
additional copper on two sides (2.5 cm
2
on the top side and 7.5 cm
2
on the down side).
Figure 3. .Printed Board Layout Example (not to scale)
With the above layout, thermal resistance junction to
ambient of 25
°
C/W can be achieved. This value being splitted
into :
. junction to case : Rthjc = 2
°
C/W
. case to ambient : Rthca = 23
°
C/W.
Lower value can be reached with the help of larger and
thicker copper metal, higher number of thermal via from top to
bottom side pcb and the use of additional thermal via from the
circuit board to the module case.
Thermal model
The junction to ambient thermal resistance of the circuit
mounted on a printed circuit board can be splitted into two
main parts: junction to case and case to ambient resistances.
A simplified steady state model is shown in figure 3 below.
Figure 4.
Simplified Thermal Model (Electrical
Equivalent)
Bottom side pcb
8 cm
2
Top side pcb
2 cm
2
HSOP20
external pcb (4x4 cm)
Thermal
via from
top to down
side pcb
Rthca
Rthjc
Junction Temp Node
(Volts represent Die
Surface Temperature)
Ambient Temp Node
Case Temp Node
Switch
Power (W)
(1.0A=1W of
Power Dissipation)
(1.0V=1
°
C Ambient Temperature)
(1.0
=1
°
C/W)
F
Freescale Semiconductor, Inc.
For More Information On This Product,
n
.
相关PDF资料 |
PDF描述 |
|---|---|
| MC33661 | LIN Enhanced Physical Interface(LIN网增强型物理接口) |
| MC33689 | System Basis Chip with LIN transceiver(带LIN收发器的系统基片) |
| MC33701 | 1.5 A Switch-Mode Power Supply with Linear Regulator(1.5 A开关方式电源，带线性稳压器) |
| MC33702 | 3.0 A Switch-Mode Power Supply with Linear Regulator(3.0 A开关方式电源，带线性稳压器) |
| MC33742 | System Basis Chip (SBC) with Enhanced High-Speed CAN Transceiver(带增强型高速CAN收发器的系统基片) |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MC33486ADH | 功能描述:电源开关 IC - 配电 DUALHIGH-SIDE BRIDGE RoHS:否 制造商:Exar 输出端数量:1 开启电阻（最大值）:85 mOhms 开启时间（最大值）:400 us 关闭时间（最大值）:20 us 工作电源电压:3.2 V to 6.5 V 电源电流（最大值）: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOT-23-5 |
| MC33486ADHR2 | 功能描述:电源开关 IC - 配电 DUALHIGH-SIDE BRIDGE RoHS:否 制造商:Exar 输出端数量:1 开启电阻（最大值）:85 mOhms 开启时间（最大值）:400 us 关闭时间（最大值）:20 us 工作电源电压:3.2 V to 6.5 V 电源电流（最大值）: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOT-23-5 |
| MC33486DH | 功能描述:IC SWITCH DUAL H-SIDE 20-HSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 电机和风扇控制器，驱动器 系列:- 标准包装:1 系列:- 应用:直流电机驱动器，步进电机驱动器 评估套件:- 输出数:1 或 2 电流 - 输出:750mA 电压 - 负载:10 V ~ 40 V 电源电压:4.5 V ~ 5.5 V 工作温度:-20°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-BFSOP（0.295"，7.50mm 宽） 供应商设备封装:24-SOP 包装:Digi-Reel® 其它名称:MTS62C19A-HS105DKR |
| MC33493ADTBE | 功能描述:射频发射器 UHF TRANSMITTER RoHS:否 制造商:Micrel 类型:ASK Transmitter 封装 / 箱体:SOT-23-6 工作频率:300 MHz to 450 MHz 封装:Reel |
| MC33493ADTBER2 | 功能描述:射频发射器 UHF TRANSMITTER RoHS:否 制造商:Micrel 类型:ASK Transmitter 封装 / 箱体:SOT-23-6 工作频率:300 MHz to 450 MHz 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。