参数资料
| 型号： | MC33742EPR2 |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 38/71页 |
| 文件大小： | 0K |
| 描述： | IC SYSTEM BASE W/CAN 48-QFN |
| 标准包装： | 2,000 |
| 应用： | 自动 |
| 接口： | SPI |
| 电源电压： | 5.5 V ~ 18 V |
| 封装/外壳： | 48-VFQFN 裸露焊盘 |
| 供应商设备封装： | 48-QFN-EP（7x7） |
| 包装： | 带卷 (TR) |
| 安装类型： | 表面贴装 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页当前第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页
Analog Integrated Circuit Device Data
Freescale Semiconductor
43
33742
FUNCTIONAL DEVICE OPERATION
OPERATIONAL MODES
In the recessive state the failure detection to GND or VSUP is possible. However, it is impossible to distinguish which bus line,
CANL or CANH, is shorted to GND or VSUP. In the dominant state, the complete diagnostic is possible once the driver is turned
on.
CAN BUS FAILURE REPORTING
CANL bus line failures (for example, CANL short to GND) is reported in the SPI register TIM1/2. CANH bus line (for example,
CANH short to VSUP) is reported in the LPC register.
In addition CAN-F and CAN-UF bits in the CAN register indicate that a CAN bus failure has been detected.
NON-IDENTIFIED AND FULLY IDENTIFIED BUS FAILURES
As indicated in Table 11, page 42, when the bus is in a recessive state it is possible to detect an error condition; however, is
it not possible to fully identify the specific error. This is called “non-identified” or “under-acquisition” bus failure. If there is no
communication (i.e., bus idle), it is still possible to warn the MCU that the SBC has started to detect a bus failure.
In the CAN register, bits D2 and D1 (CAN-F and CAN-UF, respectively) are used to signal bus failure. Bit D2 reports a bus
failure and bit D1 indicates if the failure is identified or not (bit D1 is set to logic [1} if the error is not identified).
When the detection mechanism is fully operating any bus error will be detected and reported in the TIM1/2 and LPC registers
and bit D1 will be reset to logic [0].
NUMBER OF SAMPLES FOR PROPER FAILURE DETECTION
The failure detector requires at least one cycle of recessive and dominant state to properly recognize the bus failure. The error
will be fully detected after five cycles of recessive-dominant states. As long as the failure detection circuitry has not detected the
same error for five recessive-dominant cycles, the bit “non-identified failure” (CAN-UF) will be set.
RXD PERMANENT RECESSIVE FAILURE
The purpose of this detection mechanism is to diagnose an external hardware failure at the RXD output pin and to ensure that
a permanent failure at the RXD pin does not disturb network communication.In the event RXD is shorted to a permanent high
level signal (i.e., 5.0 V), the CAN protocol module within the MCU cannot receive any incoming message. Additionally, the CAN
protocol module cannot distinguish the bus idle state and could start communication at any time. To prevent this, an RXD failure
detection, as illustrated in Figure 25 and explained below, is necessary.
Figure 25. RXD Path and RXD Permanent Recessive Detection Principle
RXD FAILURE DETECTION
The SBC senses the RXD output voltage at each LOW-to-HIGH transition of the differential receiver. Excluding internal
propagation delay, RXD output should be LOW when the differential receiver is LOW. In the event RXD is shorted to 5.0 V (e.g.,
to VDD), RXD will be tied to a high level and the RXD short to 5.0 V can be detected at the next LOW-to-HIGH transition of the
differential receiver. Compete detection requires three samples.
When the error is detected, an error flag is latched and the CAN driver is disabled. The error is reported through the SPI
register LPC, bit RXPR.
CANL
Diff Output
RXD Output
RXD Short to V1
Prop Delay
RXD Flag
RXD Flag Latched
Sampling
Sampling Sampling
Note The RXD Flag is neither the RXPR bit in the LPC register, nor the CANF bit in the INTR register.
CANH
CANL
Diff
V2
RXD Sense
RXD
TXD
60
V2
Logic
Diag
2.0 V
Driver
GND
相关PDF资料 |
PDF描述 |
|---|---|
| MC33780EG | IC DBUS MASTER DUAL DIFF 16-SOIC |
| MC33790DW | IC DSI 2-CHAN INTERFACE 16-SOIC |
| MC33794EKR2 | IC SENSOR ELECTRIC FIELD 54SOICW |
| MC33889BDW | IC SYSTEM BASE W/CAN 28-SOIC |
| MC33889DPEG | IC SYSTEM BASE W/CAN 28SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MC33742PEG | 功能描述:CAN 接口集成电路 SBC-E-HS-CAN RoHS:否 制造商:Texas Instruments 类型:Transceivers 工作电源电压:5 V 电源电流: 工作温度范围:- 40 C to + 85 C 封装 / 箱体:SOIC-8 封装:Tube |
| MC33742PEGR2 | 功能描述:CAN 接口集成电路 SBC-E-HS-CAN RoHS:否 制造商:Texas Instruments 类型:Transceivers 工作电源电压:5 V 电源电流: 工作温度范围:- 40 C to + 85 C 封装 / 箱体:SOIC-8 封装:Tube |
| MC33742PEP | 功能描述:CAN 接口集成电路 SBC-E-HS-CAN RoHS:否 制造商:Texas Instruments 类型:Transceivers 工作电源电压:5 V 电源电流: 工作温度范围:- 40 C to + 85 C 封装 / 箱体:SOIC-8 封装:Tube |
| MC33742PEPR2 | 功能描述:CAN 接口集成电路 SBC-E-HS-CAN RoHS:否 制造商:Texas Instruments 类型:Transceivers 工作电源电压:5 V 电源电流: 工作温度范围:- 40 C to + 85 C 封装 / 箱体:SOIC-8 封装:Tube |
| MC33742SDW | 功能描述:网络控制器与处理器 IC SBC-E-HS RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
发布紧急采购，3分钟左右您将得到回复。