- 您现在的位置：买卖IC网 > PDF目录1851 > MC33926PNBR2 (Freescale Semiconductor)IC H-BRIDGE THROTTLE CTRL 32-QFN PDF资料下载
参数资料
| 型号： | MC33926PNBR2 |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 13/25页 |
| 文件大小： | 0K |
| 描述： | IC H-BRIDGE THROTTLE CTRL 32-QFN |
| 标准包装： | 1 |
| 类型： | 半桥 |
| 输入类型： | 非反相 |
| 输出数： | 2 |
| 导通状态电阻： | 120 毫欧 |
| 电流 - 峰值输出： | 5A |
| 电源电压： | 5 V ~ 28 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-PowerQFN |
| 供应商设备封装： | 32-PQFN（8x8） |
| 包装： | 标准包装 |
| 其它名称： | MC33926PNBR2DKR |
FUNCTIONAL DESCRIPTION
FUNCTIONAL PIN DESCRIPTION
device circuitry is fully operational and the supply
I PWR(STANDBY) current is reduced to a few mA. Refer to Table
H-BRIDGE OUTPUT (OUT1, OUT2)
These pins are the outputs of the H-Bridge with integrated
freewheeling diodes. T h e bridge output is controlled using
the IN1, IN2, D1, and D2 inputs. The outputs have PWM
current limiting above the I LIM threshold. The outputs also
have thermal shutdown (tri-state latch-OFF) with hysteresis
as well as short-circuit latch-OFF protection.
A disable timer (time t B ) is incorporated to distinguish
between load currents that are higher than the I LIM threshold
and short-circuit currents. This timer is activated at each
output transition.
CHARGE PUMP CAPACITOR (CCP)
This pin is the charge pump output pin and connection for
the external charge pump reservoir capacitor. The allowable
value is from 30 nF to 100 nF. This capacitor must be
connected from the CCP pin to the VPWR pin. The device
cannot operate properly without the external reservoir
capacitor.
ENABLE INPUT (EN)
The EN pin is used to place the device in a Sleep mode so
a logic LOW state, the device is in Sleep mode. The device is
enabled and fully operational when the EN pin voltage is in
logic HIGH. An internal pulldown resistor maintains the
device in Sleep mode in the event EN is driven through a
high-impedance I/O, or an unpowered microcontroller, or the
EN input becomes disconnected.
FEEDBACK (FB)
The 33926 has a feedback output (FB) for “real time”
monitoring of H-Bridge high-side output currents to facilitate
closed-loop operation for motor speed and torque control.
The FB pin provides current sensing feedback of the
H-Bridge high side drivers. When running in the forward or
reverse direction, a ground-referenced 0.24% of load current
is output to this pin. Through the use of an external resistor to
ground, the proportional feedback current can be converted
to a proportional voltage equivalent and the controlling
microcontroller can “read” the current proportional voltage
with its analog-to-digital converter (ADC). This is intended to
provide the user with only first-order motor current feedback
for motor torque control. The resistance range for the linear
operation of the FB pin is 100 < R FB < 300 Ω .
If PWM-ing is implemented using the disable pin inputs
(either D1 or D2 ), a small filter capacitor (~1.0 μF) may be
required in parallel with the R FB resistor to ground for spike
suppression.
as to consume very low currents. When the EN pin voltage is
33926
Analog Integrated Circuit Device Data
Freescale Semiconductor
13
相关PDF资料 |
PDF描述 |
|---|---|
| MC33931VWR2 | IC H-BRIDGE THROTTLE CTRL 44HSOP |
| MC33932VW | IC H-BRIDGE THROTTLE CTRL 44HSOP |
| MC33970DWR2 | IC GAUGE DRIVER SPI 24-SOIC |
| MC33981BPNAR2 | IC SWITCH HI SIDE SINGLE 16-PQFN |
| MC33984BPNAR2 | IC SWITCH HI SIDE DUAL 16-PQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MC33931EK | 功能描述:马达/运动/点火控制器和驱动器 5A H-BRIDGE RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| MC33931EKR2 | 制造商:Freescale Semiconductor 功能描述:MISC 制造商:Freescale Semiconductor 功能描述:IC MOTOR DRIVER PAR 32SOIC 制造商:Freescale Semiconductor 功能描述:5A H-BRIDGE |
| MC33931VW | 功能描述:马达/运动/点火控制器和驱动器 5A H-BRIDGE RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| MC33931VWR2 | 功能描述:马达/运动/点火控制器和驱动器 5A H-BRIDGE RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| MC33932EK | 制造商:Freescale Semiconductor 功能描述:H-Bridge 制造商:Freescale Semiconductor 功能描述:MC33932EK - Bulk 制造商:Freescale Semiconductor 功能描述:IC MOTOR DRIVER PAR 54SOIC 制造商:Freescale Semiconductor 功能描述:5A H-BRIDGE |
发布紧急采购，3分钟左右您将得到回复。