- 您现在的位置：买卖IC网 > PDF目录1851 > MC33926PNBR2 (Freescale Semiconductor)IC H-BRIDGE THROTTLE CTRL 32-QFN PDF资料下载
参数资料
| 型号： | MC33926PNBR2 |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 17/25页 |
| 文件大小： | 0K |
| 描述： | IC H-BRIDGE THROTTLE CTRL 32-QFN |
| 标准包装： | 1 |
| 类型： | 半桥 |
| 输入类型： | 非反相 |
| 输出数： | 2 |
| 导通状态电阻： | 120 毫欧 |
| 电流 - 峰值输出： | 5A |
| 电源电压： | 5 V ~ 28 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-PowerQFN |
| 供应商设备封装： | 32-PQFN（8x8） |
| 包装： | 标准包装 |
| 其它名称： | MC33926PNBR2DKR |
FUNCTIONAL DEVICE OPERATION
PROTECTION AND DIAGNOSTIC FEATURES
PROTECTION AND DIAGNOSTIC FEATURES
SHORT-CIRCUIT PROTECTION
If an output short-circuit condition is detected, the power
outputs tri-state (latch-OFF) independent of the input (IN1
and IN2) states, and the fault status output flag (SF) is SET
to a logic LOW. If the D1 input changes from a logic HIGH to
logic LOW, or if the D2 input changes from a logic LOW to
logic HIGH, the output bridge will become operational again,
and the fault status flag will be reset (cleared) to a logic HIGH
state.
The output stage will always switch into the mode defined
by the input pins (IN1, IN2, D1, and D2), provided the device
junction temperature is within the specified operating
temperature range.
OVER-TEMPERATURE SHUTDOWN AND
HYSTERESIS
If an over-temperature condition occurs, the power outputs
are tri-stated (latched-OFF), and the fault status flag (SF) is
SET to a logic LOW.
To reset from this condition, D1 must change from a logic
HIGH to logic LOW, or D2 must change from a logic LOW to
logic HIGH. When reset, the output stage switches ON again,
provided that the junction temperature is now below the over-
temperature threshold limit minus the hysteresis.
Important Resetting from the fault condition will clear the
fault status flag. Powering down and powering up the device
will also reset the 33926 from the fault condition.
INTERNAL PWM CURRENT LIMITING
The maximum current flow under normal operating
conditions should be less than 5.0 A. The instantaneous load
currents will be limited to I LIM via the internal PWM current
limiting circuitry. When the I LIM threshold current value is
reached, the output stages are tri-stated for a fixed time (T A )
of 20 μs typical. Depending on the time constant associated
with the load characteristics, the output current decreases
during the tri-state duration until the next output ON cycle
occurs.
The PWM current limit threshold value is dependent on the
OUTPUT AVALANCHE PROTECTION
If VPWR were to become an open circuit, the outputs
would likely tri-state simultaneously due to the disable logic.
This could result in an unclamped inductive discharge. The
VPWR input to the 33926 should not exceed 40 V during this
transient condition, to prevent electrical overstress of the
output drivers.This can be accomplished with a zener clamp
or MOV, and/or an appropriately valued input capacitor with
sufficiently low ESR (see Figure 13 ).
device junction temperature. When - 40°C < T J < 160°C, I LIM is
between the specified minimum/maximum values. When T J
exceeds 160 °C, the I LIM threshold decreases to 4.2 A.
Shortly above 175 °C the device over-temperature circuit will
VPW R
Bulk
VPW R
detect T LIM and an over-temperature shutdown will occur.
This feature implements a graceful degradation of operation
before thermal shutdown occurs, thus allowing for
intermittent unexpected mechanical loads on the motor ’s
Low ESR
Cap.
100nF
OUT1
M
gear-reduction train to be handled.
Important Die temperature excursions above 150 ° C are
permitted only for non-repetitive durations < 30 seconds.
9
I/Os
OUT2
Provision must be made at the system level to prevent
prolonged operation in the current-foldback region.
AGND
PGND
Figure 13. Avalanche Protection
33926
Analog Integrated Circuit Device Data
Freescale Semiconductor
17
相关PDF资料 |
PDF描述 |
|---|---|
| MC33931VWR2 | IC H-BRIDGE THROTTLE CTRL 44HSOP |
| MC33932VW | IC H-BRIDGE THROTTLE CTRL 44HSOP |
| MC33970DWR2 | IC GAUGE DRIVER SPI 24-SOIC |
| MC33981BPNAR2 | IC SWITCH HI SIDE SINGLE 16-PQFN |
| MC33984BPNAR2 | IC SWITCH HI SIDE DUAL 16-PQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MC33931EK | 功能描述:马达/运动/点火控制器和驱动器 5A H-BRIDGE RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| MC33931EKR2 | 制造商:Freescale Semiconductor 功能描述:MISC 制造商:Freescale Semiconductor 功能描述:IC MOTOR DRIVER PAR 32SOIC 制造商:Freescale Semiconductor 功能描述:5A H-BRIDGE |
| MC33931VW | 功能描述:马达/运动/点火控制器和驱动器 5A H-BRIDGE RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| MC33931VWR2 | 功能描述:马达/运动/点火控制器和驱动器 5A H-BRIDGE RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| MC33932EK | 制造商:Freescale Semiconductor 功能描述:H-Bridge 制造商:Freescale Semiconductor 功能描述:MC33932EK - Bulk 制造商:Freescale Semiconductor 功能描述:IC MOTOR DRIVER PAR 54SOIC 制造商:Freescale Semiconductor 功能描述:5A H-BRIDGE |
发布紧急采购，3分钟左右您将得到回复。