- 您现在的位置：买卖IC网 > PDF目录19707 > MC34652EFR2 (Freescale Semiconductor)IC CTRLR HOT SWAP NEG V 16-SOIC PDF资料下载
参数资料
| 型号： | MC34652EFR2 |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 11/26页 |
| 文件大小： | 1802K |
| 描述： | IC CTRLR HOT SWAP NEG V 16-SOIC |
| 标准包装： | 2,500 |
| 类型： | 热交换开关 |
| 应用： | 通用 |
| 内部开关： | 是 |
| 电流限制： | 2A |
| 电源电压： | 15 V ~ 80 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 16-SOIC N |
| 包装： | 带卷 (TR) |
Analog Integrated Circuit Device Data
Freescale Semiconductor
11
34652
FUNCTIONAL DESCRIPTION
FUNCTIONAL PIN DESCRIPTION
rchived by Freescale Semiconductor, Inc., 2008
POWER GOOD OUTPUT (ACTIVE LOW) (PG
)
The PG
pin is the active low power good output signal that
is used to enable or disable a load. This signal goes active
after a successful power-up sequence and stays active as
long as the device is in normal operation and is not
experiencing any faults.
The signal is deactivated under the following conditions:
" Power is turned off.
" The device is disabled for more than 1.0 ms.
" The device exceeded its thermal shutdown threshold for
more than 12 約.
" The device is in overvoltage or undervoltage mode for
more than 1.0 ms.
" Load current exceeded the overcurrent limit for more than
3.0 ms.
This pin is referenced to VIN.
OUTPUT VOLTAGE (VOUT)
The VOUT
pin is the drain of the internal Power MOSFET
and supplies a current-limited voltage to the load. The load
connects between the VOUT and VPWR pins.
START-UP AND RETRY DELAY TIMER (TIMER)
This input is used to control the time-base used to
generate the timing sequences at start-up and the retry delay
when the device experiences any fault. The TIMER pin can
be left unconnected for a default timer value of 200 ms or the
user can connect a resistor between this pin and the VIN
pin
to set the timer value externally. The timer value can vary
between 100 ms and 1000 ms.
OVERVOLTAGE CONTROL (OV)
The OV pin is used to set the upper limit of the input
voltage operation range. If the OV pin voltage goes above the
overvoltage threshold value, the device turns off the internal
Power MOSFET and deactivates the two power good
outputs, PG and PG
. The Power MOSFET stays off until the
OV drops below the threshold value. The overvoltage
detection circuit has a 1.0 ms filter timer.
The OV pin can be left unconnected for the typical default
threshold value of 78
V or the user can set the threshold
value externally with a simple voltage divider using resistors
between the VPWR and VIN pins.
UNDERVOLTAGE CONTROL (UV)
The UV pin is used to set the lower limit of the input voltage
operation range. If the UV pin voltage goes below the
undervoltage threshold value, the device turns off the internal
Power MOSFET and deactivates the two power good
outputs, PG and PG
. The Power MOSFET stays off until the
UV rises above the threshold value. The undervoltage
detection circuit has a 1.0 ms filter timer.
The UV pin can be left unconnected for the typical default
threshold value of 37 V or the user can set the threshold
value externally with a simple voltage divider using resistors
between the VPWR and VIN pins.
POSITIVE SUPPLY VOLTAGE INPUT (VPWR)
The VPWR
pin is the most-positive power supply input.
The load connects between the VPWR
and VOUT pins.
DISABLE INPUT CONTROL (DISABLE)
The DISABLE pin is used to easily disconnect or connect
the load from the main power line by disabling or enabling the
34652. It can also be used to reset the fault conditions that
cause a Power No Good signal.
If left open or connected to VPWR, the DISABLE pin is
inactive and the device is enabled. If a positive voltage
(above V
PWR
) or a negative voltage (below V
PWR
) is applied
to DISABLE, it is active and the device is disabled. The
disable function has a 1.0 ms filter timer.
This pin is referenced to VPWR.
CURRENT LIMIT CONTROL (ILIM)
The ILIM pin is used to set the overcurrent limit during
normal operation. This pin can be left unconnected for a
default overcurrent limit value of 1.0 A or the user can
connect an external resistor between the ILIM and VIN pins
to set the overcurrent limit value. This value can vary
between 0.35 A and 2.25 A. The overcurrent detection circuit
has a 100 約 filter timer.
CHARGING CURRENT LIMIT CONTROL (ICHG)
The ICHG pin is used to set the current limit that is used to
charge the loads input capacitor, hence limiting the inrush
current to a known constant value. This pin can be left
unconnected for a default charging current limit value of 0.1 A
and a default I
CHG
rise time of 1.0 ms. Or the user can
connect an external resistor between the ICHG
and VIN pins
to set the current limit value between 0.05 A and 0.5 A and an
相关PDF资料 |
PDF描述 |
|---|---|
| CR2450 | BATTERY LITHIUM COIN 3V CELL |
| VI-243-CY-F4 | CONVERTER MOD DC/DC 24V 50W |
| V48A3V3E264BG3 | CONVERTER MOD DC/DC 3.3V 264W |
| VI-243-CY-F3 | CONVERTER MOD DC/DC 24V 50W |
| PAF600F280-28/T | DC-DC CONVERTR 28VDC 602W 21.5A |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MC34653 | 制造商:SPC Multicomp 功能描述:HEADER R/A SQ PIN 2.54MM 10WAY 制造商:SPC Multicomp 功能描述:HEADER, R/A, SQ PIN, 2.54MM, 10WAY 制造商:SPC Multicomp 功能描述:WIRE-BOARD CONN, HEADER, 10POS, 2.54MM; Connector Type:Wire to Board; Series:2217; Contact Termination:Through Hole Right Angle; Gender:Header; No. of Contacts:10; No. of Rows:1; Pitch Spacing:2.54mm; Contact Plating:Tin ;RoHS Compliant: Yes |
| MC34653EF | 功能描述:热插拔功率分布 1A 8-LD NVHS RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| MC34653EFR2 | 功能描述:热插拔功率分布 1A 8-LD NVHS RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| MC34655 | 制造商:SPC Multicomp 功能描述:HEADER SQUARE PIN 2.54MM 5WAY 制造商:SPC Multicomp 功能描述:HEADER, SQUARE PIN, 2.54MM, 5WAY 制造商:SPC Multicomp 功能描述:WIRE-BOARD CONNECTOR HEADER 5POS, 2.54MM; Connector Type:Wire to Board; Series:2217; Contact Termination:Through Hole Vertical; Gender:Header; No. of Contacts:5; No. of Rows:1; Pitch Spacing:2.54mm; Contact Plating:Tin ;RoHS Compliant: Yes |
| MC34657 | 制造商:SPC Multicomp 功能描述:HEADER VERTICAL 2WAY 制造商:SPC Multicomp 功能描述:HEADER, VERTICAL, 2WAY 制造商:SPC Multicomp 功能描述:WIRE-BOARD CONNECTOR, RCPT, 2POS, 4.2MM; Series:2266(5566)S; Pitch Spacing:4.2mm; Contact Termination:Through Hole Vertical; No. of Contacts:2; No. of Rows:2; Connector Mounting:PCB; Gender:Receptacle; Contact Material:Copper Alloy ;RoHS Compliant: Yes |
发布紧急采购，3分钟左右您将得到回复。