- 您现在的位置：买卖IC网 > PDF目录376152 > MC3510 (Electronic Theatre Controls, Inc.) ECONOLINE: RSZ/P - 1kVDC PDF资料下载
参数资料
| 型号： | MC3510 |
| 厂商： | Electronic Theatre Controls, Inc. |
| 元件分类： | 8位微控制器 |
| 英文描述： | ECONOLINE: RSZ/P - 1kVDC |
| 中文描述： | ECONOLINE：RSZ / P - 1kVDC 2kVDC隔离UL94V - 0封装材料所需的散热片，无外置。组件所需的环形磁ContinuousShort电路保护（/ P的后缀） |
| 文件页数： | 29/75页 |
| 文件大小： | 1023K |
| 代理商： | MC3510 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页当前第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页
MC3510 Technical Specifications
29
6 Parallel Communication
With the addition of an external logic device, the Pilot motion processor can communicate with a
host processor using a parallel data stream. This offers a higher communication rate than a serial
interface and may be used in configurations where a serial connection is not available or not
convenient. This section details the required logic that must be implemented in the external device
as well as the necessary connections to the CP chip.
The reference design files for the parallel interface chip, in Actel/ViewLogic format, are available
from PMD. There are two versions of the design, one for interfacing with host processors that have
an 8-bit data bus and one for host processors that have a 16-bit data bus. The designs are called
IOPIL8 and IOPIL16 respectively. The interface to the CP chip is essentially identical in both.
The function of the I/O chip is to provide a shared-memory style interface between the host and CP
chip, comprised of four 16-bit wide locations. These are used for transferring commands and data
between the host and Pilot motion processor. The CP chip accesses the command/data registers
using its 16-bit external data bus while the host accesses the registers via a parallel interface with chip
select, read, write and command/data signals. If necessary, the host side interface can be modified
by the designer to match specific requirements of the host processor.
6.1
Host interface pin description table
Pin Name
HostCmd
Direction
input
Description
This signal is asserted
high
to write a host instruction to the motion processor, or to
read the status of the
HostRdy
and
HostIntrpt
signals. It is asserted
low
to read or write
a data word.
This signal is used to synchronize communication between the motion processor
and the host.
HostRdy
will go
low
(indicating host port busy) at the end of a read or
write operation according to the interface mode in use, as follows:
Interface Mode
HostRdy
goes low
8/16
after the second byte of the instruction word
after the second byte of each data word is transferred
16/16
after the 16-bit instruction word
after each 16-bit data word
serial
n/a
HostRdy
will go
high,
indicating that the host port is ready to transmit, when the last
transmission has been processed. All host port communications must be made
with
HostRdy
high
(ready).
A typical busy-to-ready cycle is 12.5 microseconds, but can be substantially longer,
up to 100 microseconds.
When
~HostRead
is
low
, a data word is read from the motion processor.
When
~HostWrite
is
low
, a data word is written to the motion processor.
When
~HostSlct
is
low
, the host port is selected for reading or writing operations.
I/O chip to CP chip interrupt. This signal sends an interrupt to the CP chip
whenever a host–chipset transmission occurs. It should be connected to CP chip
pin 53,
I/OIntrpt
.
This signal is
high
when the I/O chip is reading data from the I/O chip, and
low
when it is writing data. It should be connected to CP chip pin 4,
R/W
.
This signal goes
low
when the data and address become valid during Motion
processor communication with peripheral devices on the data bus, such as external
memory or a DAC. It should be connected to CP chip pin 6,
Strobe
.
HostRdy
output
~HostRead
~HostWrite
~HostSlct
CPIntrpt
input
input
input
output
CPR/~W
input
CPStrobe
input
相关PDF资料 |
PDF描述 |
|---|---|
| MC3750 | MC3750 |
| MC380A2 | MC380A2 |
| MC382A2 | MC380A2 |
| MC401 | 4 wide 3-2-2-3 input expander for and-or-invert gae |
| MC409 | 4 wide 3-2-2-3 input expander for and-or-invert gae |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MC35100V10000A99 | 制造商:SUNON 功能描述:- Bulk |
| MC35100V1000UA99 | 制造商:SUNON 功能描述:5 VDC, 2 FIOS, 35X35X10MM, 150MA, 0.8W, 9500 RPM, 6.5-7.0 CF - Bulk |
| MC35100V1-000U-A99 | 功能描述:FAN 35X10MM 5VDC 0.75W 7CFM RoHS:是 类别:风扇，热管理 >> 风扇 - DC 系列:M 其它有关文件:Part Number Break-Down and Other Notes 产品培训模块:Fan Options 产品目录绘图:Square Flange 标准包装:54 系列:AFB 风扇类型:管轴式 尺寸/尺寸:方形 - 120mm L x 120mm H x 25.4mm W 电压 - 额定:12VDC 功率（瓦特）:2.76W 特点:- RPM:2500 RPM 杂讯:38.5 dB（A） 静态压力:0.246 英寸水柱（61.3 Pa） 气流:82.7 CFM（2.34m³/min） 端子:2 引线 轴承类型:滚珠 工作温度:- 重量:0.436 磅（197.77g） 额定电流:0.230A 电压范围:7 ~ 13.8VDC 预期寿命:- 产品目录页面:2694 (CN2011-ZH PDF) 相关产品:1053-1407-ND - FAN GUARD 120MM WIRE MESH BLACK1053-1406-ND - FAN GUARD 120MM WIRE MESH NATURL1053-1397-ND - FAN GUARD LOUVERED 120MM BLACK1053-1387-ND - FAN FILTER 120MM 45PPI1053-1386-ND - FAN FILTER 120MM 30PPI1053-1362-ND - FAN GUARD PLASTIC 120MM PUSH ON1053-1361-ND - FAN GUARD PLASTIC 120MM1053-1359-ND - FAN GUARD METAL 120MM1053-1358-ND - FAN GUARD METAL 120MM BLACK1053-1357-ND - FAN GUARD METAL 120MM更多... 其它名称:603-1075 |
| MC35100V1000UF99 | 制造商:SUNON 功能描述:- Bulk |
| MC35100V1-000U-F99 | 功能描述:FAN DC 35X10 5V .15A 9500RPM RoHS:是 类别:风扇，热管理 >> 风扇 - DC 系列:M 其它有关文件:2406KL UL Report 产品培训模块:Cooling Solutions Computer Cooling in System Design Thermal Simulation in Telecom Applications RoHS指令信息:2406KL-05W-B39-L50 Material 标准包装:150 系列:2406KL 风扇类型:管轴式 尺寸/尺寸:方形 - 60mm L x 60mm H x 15mm W 电压 - 额定:24VDC 功率（瓦特）:1.44W 特点:速度传感器（转速计） RPM:3600 RPM 杂讯:28 dB 静态压力:0.125 英寸水柱（31.1 Pa） 气流:14.1 CFM（0.399m³/min） 端子:3 引线 轴承类型:滚珠 工作温度:14 ~ 140°F（-10 ~ 60°C） 重量:0.099 磅（44.91g） 额定电流:0.060A 电压范围:12 ~ 27.6VDC 预期寿命:25°C 时为 70000 小时 相关产品:8467K-ND - GUARD FAN FOR 2 1/2" FAN PLASTIC8465K-ND - GUARD ASSY 2.36"SQ FOR 2 1/2"FAN 其它名称:2406KL05WB39L502406KL05WB39L50-ND |
发布紧急采购，3分钟左右您将得到回复。