- 您现在的位置：买卖IC网 > PDF目录16584 > MC3PHACVFAE (Freescale Semiconductor)IC MOTOR CONTROLLER 32QFP PDF资料下载
参数资料
| 型号： | MC3PHACVFAE |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 12/36页 |
| 文件大小： | 0K |
| 描述： | IC MOTOR CONTROLLER 32QFP |
| 标准包装： | 250 |
| 应用： | AC 电机控制器，3 相 |
| 输出数： | 1 |
| 电源电压： | 4.5 V ~ 5.5 V |
| 工作温度： | -40°C ~ 105°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-LQFP |
| 供应商设备封装： | 32-LQFP（7x7） |
| 包装： | 托盘 |
| 产品目录页面： | 808 (CN2011-ZH PDF) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页当前第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
Features
illustrated in Figure 6 . To compensate for this voltage loss, the voltage profile is boosted over the normal
voltage curve in Figure 5 , so that the magnetizing current remains constant over the speed range.
100%
VOLTAGE BOOST
CO
MP
E
NS
A
TIO
NF
O
RS
TA
T
OR
L
OS
SE
S
FREQUENCY
BASE FREQUENCY
Figure 5. Voltage Profiling, Including Voltage Boost
PARASITICS
X 1
R 1
X 2
R 2
MAGNETIZING CURRENT
(TRY TO KEEP CONSTANT)
X M
TORQUE CURRENT
R2 (1 –s)
s
Figure 6. AC Motor Single Phase Model Showing Parasitic Stator Impedances
The MC3PHAC allows the voltage boost to be specified as a percentage of full voltage at 0 Hz, as shown
in Figure 5 . In standalone mode, voltage boost is specified during the initialization phase by supplying
a voltage to the MUX_IN pin while the VBOOST_MODE pin is being driven low. Refer to the graph in
Figure 11 for the resistance value versus voltage boost. Figure 11 assumes a 6.8 k ? pullup resistor. In
this way, voltage boost can be specified from 0 to 40 percent, with a scaling factor of 8 percent per volt.
In PC master software mode, the voltage boost can be specified from 0 to 100 percent and can be
changed at anytime.
By using the voltage boost value, and the specified base frequency, the MC3PHAC has all the information
required to generate a voltage profile automatically based on the generated waveform frequency. An
additional feature exists in PC master software mode whereby this voltage value can be overridden and
controlled in real time. Specifying a voltage lower than the normal volts-per-hertz profile permits a softer
torque response in certain ergonomic situations. It also allows for load power factor control and higher
operating efficiencies with high inertia loads or other loads where instantaneous changes in torque
demand are not permitted. Details of this feature are discussed in the PC Master Software Operation with
PLL Clock Generation — The OSC1 pin signal is used as a reference clock for an internal PLL clocking
circuit, which is used to drive the internal clocks of the MC3PHAC. This provides excellent protection
against noise spikes that may occur on the OSC1 pin. In a clocking circuit that does not incorporate a PLL,
a noise spike on the clock input can create a clock edge, which violates the setup times of the clocking
MC3PHAC Monolithic Intelligent Motor Controller, Rev. 2
12
Freescale Semiconductor
相关PDF资料 |
PDF描述 |
|---|---|
| ZXBM1016ST20TA | IC MOTOR CTRLR 1PH TSSOP20 |
| VI-J1W-EZ-S | CONVERTER MINIMOD DC/DC 5.5V 25W |
| EEU-FR1J391 | CAP ALUM 390UF 63V 20% RADIAL |
| AMIS30623C6238RG | IC MOTOR DRIVER/CTLR 20SOIC |
| PX0840/A/2M00 | CABLE PLUG IP68 USB A-B 2M |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MC3PHACVP | 制造商:Freescale Semiconductor 功能描述:MCU 8BIT HC08 CISC 8KB FLASH 5V 28PDIP - Rail/Tube 制造商:Freescale Semiconductor 功能描述:Controller IC |
| MC3PHACVPE | 功能描述:马达/运动/点火控制器和驱动器 8BIT MCU 8K FLASH OTP RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| MC3S12C128 | 制造商:MOTOROLA 制造商全称:Motorola, Inc 功能描述:16-Bit Microcontroller |
| MC3S12C32 | 制造商:MOTOROLA 制造商全称:Motorola, Inc 功能描述:16-Bit Microcontroller |
| MC3S12C64 | 制造商:MOTOROLA 制造商全称:Motorola, Inc 功能描述:16-Bit Microcontroller |
发布紧急采购，3分钟左右您将得到回复。