参数资料
型号: MC3PHACVFAE
厂商: Freescale Semiconductor
文件页数: 14/36页
文件大小: 0K
描述: IC MOTOR CONTROLLER 32QFP
标准包装: 250
应用: AC 电机控制器,3 相
输出数: 1
电源电压: 4.5 V ~ 5.5 V
工作温度: -40°C ~ 105°C
安装类型: 表面贴装
封装/外壳: 32-LQFP
供应商设备封装: 32-LQFP(7x7)
包装: 托盘
产品目录页面: 808 (CN2011-ZH PDF)
Features
?
Regeneration Control — Regeneration is a process by which stored mechanical energy in the
motor and load is transferred back into the drive electronics, usually as a result of an aggressive
deceleration operation. In special cases where this process occurs frequently (for example,
elevator motor control systems), it is economical to incorporate special features in the motor drive
to allow this energy to be supplied back to the ac mains. However, for most low cost ac drives, this
energy is stored in the dc bus capacitor by increasing its voltage. If this process is left unchecked,
the dc bus voltage can rise to dangerous levels, which can destroy the bus capacitor or the
transistors in the power inverter.
The MC3PHAC incorporates two techniques to deal with regeneration before it becomes a
problem:
14
Resistive Braking — The DC_BUS pin is monitored at a 5.3 kHz frequency (4.0 kHz when the
PWM frequency is set to 15.9 kHz), and when the voltage reaches a certain threshold, the
RBRAKE pin is driven high. This signal can be used to control a resistive brake placed across
the dc bus capacitor, such that mechanical energy from the motor will be dissipated as heat in
the resistor versus being stored as voltage on the capacitor. In standalone mode, the DC_BUS
threshold required to assert the RBRAKE signal is fixed at 3.85 volts (110 percent of nominal)
where nominal is defined to be 3.5 volts. In PC master software mode, this threshold can be
set to any value between 0 volts (0 percent of nominal) and greater than 5 volts (143 percent
of nominal) and can be changed at any time.
Automatic Deceleration Control — When decelerating the motor, the MC3PHAC attempts to
use the specified acceleration value for deceleration as well. If the voltage on the DC_BUS pin
reaches a certain threshold, the MC3PHAC begins to moderate the deceleration as a function
of this voltage, as shown in Figure 7 . The voltage range on the DC_BUS pin from when the
deceleration begins to decrease, to when it reaches 0, is 0.62 volts. In standalone mode, the
DC_BUS voltage where deceleration begins to decrease is fixed at 3.85 volts (110 percent of
nominal) where nominal is defined to be 3.5 volts. In PC master software mode, this threshold
can be set to any value between 0 volts (0 percent of nominal) and greater than 5 volts (143
percent of nominal) and can be changed at any time.
ACCELERATION INPUT
BUS VOLTAGE
BEGIN MODERATING DECEL
(LEVEL IS PROGRAMMABLE
IN PC MASTER SOFTWARE MODE)
Figure 7. Deceleration as a Function of Bus Voltage
MC3PHAC Monolithic Intelligent Motor Controller, Rev. 2
Freescale Semiconductor
相关PDF资料
PDF描述
ZXBM1016ST20TA IC MOTOR CTRLR 1PH TSSOP20
VI-J1W-EZ-S CONVERTER MINIMOD DC/DC 5.5V 25W
EEU-FR1J391 CAP ALUM 390UF 63V 20% RADIAL
AMIS30623C6238RG IC MOTOR DRIVER/CTLR 20SOIC
PX0840/A/2M00 CABLE PLUG IP68 USB A-B 2M
相关代理商/技术参数
参数描述
MC3PHACVP 制造商:Freescale Semiconductor 功能描述:MCU 8BIT HC08 CISC 8KB FLASH 5V 28PDIP - Rail/Tube 制造商:Freescale Semiconductor 功能描述:Controller IC
MC3PHACVPE 功能描述:马达/运动/点火控制器和驱动器 8BIT MCU 8K FLASH OTP RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube
MC3S12C128 制造商:MOTOROLA 制造商全称:Motorola, Inc 功能描述:16-Bit Microcontroller
MC3S12C32 制造商:MOTOROLA 制造商全称:Motorola, Inc 功能描述:16-Bit Microcontroller
MC3S12C64 制造商:MOTOROLA 制造商全称:Motorola, Inc 功能描述:16-Bit Microcontroller